Dishwasher Parts

We scoured the web and there are few references to this so I want to add it in case it helps. Replacing hinges solved the popping opening issue. We could not solve our dishwasher door issue after a number of other tries: Latch, Catch, Ropes that attach to the springs that pull the door closed. I tend to believe the solve could be different b/c all these things work together. But for us, we were skeptical that the hinge swap would work and we were very pleasantly surprised. Read more

Took cover completely off and tried putting back, could not match up left screw with available screw hole. Tried many different configurations and sequences to make this happen. watched a video on changing the front panel, the door in it had four screws, mine 2, no help there. Searched on the hyperextending issue, found an article about dogs and kids [had both here] climbing on the door and to check the springs and linkages. Linkages intact both sides, R [opposite] side spring very stretched.... Read more

Changed the water pressure sensor Read more

We knew at least one door hinge cable assembly or hinge spring was broken (the door started falling down rapidly and became heavy to close) so we ordered two of each since we had read to go ahead and replace the damaged items on both sides. While we were waiting on the order, the other side must have broken-the door became incredibly heavy and instead of falling open, started crashing down unless it was carefully lowered. We feared it would fall on one of our animals and kill them. We did not... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Won't start
• Door latch failure

Discovered that the common cause of the problem was the latch in the door. Found a video online that showed the exact procedure for my model dishwasher. Ordered the part from AppliancePartsPros on a Thursday afternoon and it was in my hands by noon on Friday. Carefully took the door apart, compared parts, reassembled, and the joy on my wife's face was priceless when the dishwasher started up without doing anything special. Do not be afraid to attempt this repair. Read more

Replaced with new kickplate panel. Didn't exactly match our unit but was the right length & lined up correctly enough to allow me to zip tie it to the frame properly. Read more

Replaced spray arms and tube. Found all had debris in them and prohibited water pressure from reaching items. After replacement everything comes out sparkling. Don't understand how the spray arms getting plugged. Almost like waste water is recycled. Turns out to be a very easy project and if needed AppliancePartsPro has information and directions available at your finger tips.! Read more

I watched the video on your site and it showed step by step how to replace the spring. Excellent shipping time. Good customer service on chat forum. Read more

Web site helped me diagnose problem as water inlet valve not fully shutting off. Repairman quoted me 200.00 to fix, so I decided to gamble the price of the item and repair myself. Web site offered easy to follow, detailed video instructions, had the part replaced and back to working like new in less than 30 minutes. Read more

The replacement arm arrived promptly. Removing the old spray arm hub was very difficult by hand, plumbers wrench, or adjustable wrench. However, by inserting a screwdriver trough the two opposite holes where the tabs had broken off, it is relatively easy to unscrew the old hub. Read more

Replaced switch Read more

The old fascia had broken and been torn off. I should have saved the buttons from it, but I didn't know that I'd be repairing it - I figured I would have to replace the unit. Well, money is tight, so I got the model number from the unit and looked up parts online. I couldn't find the exact model number on this site, but the picture of the fascia looked just like the picture in my manual, so I bought it, a handle strip, and a new set of buttons. I pulled the stainless panel off the front, then... Read more

Replace rope on one side Read more

We ordered the dispenser cover kit. the problem was with the spring. followed your "how to" video and it was a quick and easy fix! Read more