Fuse Or Sensor

If your range won't reach set temperature or displays incorrect readings, the temperature sensor likely failed. This probe-style RTD sensor restores accuracy.

This oven temperature probe is the internal sensor that monitors cooking cavity temperature so the oven control can regulate heat for accurate cooking and bake results. It's a direct-replacement sensing probe for compatible Bosch ovens. What it does:

• Measures internal oven temperature and sends readings to the control board
• Allows the oven to maintain set temperatures for consistent cooking
• Common symptoms of a failing probe: inaccurate oven temps, oven not reaching set temperature, or temperature-related error codes
• Works with the oven's control system to help cycle heating elements or gas valve

• Disconnect power to the appliance before servicing to avoid shock hazard
• Handle the probe and its wiring gently; avoid sharp bends or pulling on connectors
• Verify connector orientation and secure connections to the control board per OEM diagram

This noise filter reduces electromagnetic interference generated by the microwave's electronics, preventing it from affecting other nearby appliances or electronic devices. It is typically located near the power input inside the microwave cabinet. Replace this filter if the microwave causes static on radios or TVs, trips breakers intermittently, or if the filter shows visible signs of burning or damage.

This probe thermistor monitors interior temperature and sends readings to the control board so your appliance can maintain the correct cooling cycle. It replaces a failed or inaccurate sensor to help restore proper temperature regulation. What it does:

• Senses air or evaporator temperature and reports it to the control module
• Commonly related to warm/freezing issues, incorrect temperature readings, or erratic cycling
• Used by the control system to trigger fans, defrost, and compressor operation as needed
• Works as a direct replacement for the listed OEM temperature probe

• Disconnect power before replacing to avoid shock or damage
• Handle the sensor tip and wiring gently to avoid damage to the element or insulation
• Route and secure the wiring so it does not contact moving parts or hot surfaces

5 A, 125 V electrical fuse that restores circuit protection when the original fuse is blown. Replacing the failed fuse helps prevent further electrical damage and can restore normal appliance operation. What it does:

• Provides overcurrent protection for the appliance circuit to stop excessive current flow.
• Replaces a blown or open fuse that prevents the appliance from powering up.
• Common symptom: appliance has no power or a circuit/component won't operate.
• Common symptom: intermittent power or a fuse that visibly shows a blown element.

• Always disconnect power (unplug or shut off breaker) before inspecting or replacing the fuse.
• Replace only with the exact rated fuse (5 A, 125 V) and part number to maintain proper protection.
• Do not bypass the fuse or use makeshift substitutes — that can cause fire or equipment damage.

This fixed thermostat monitors and limits temperature to protect the appliance's system and components. It's a simple, non-adjustable sensor/limit switch used where a set cutoff temperature is required for safe operation. What it does:

• Opens or cuts power when the monitored temperature reaches its fixed limit to prevent overheating
• Helps stop continuous heating cycles caused by a failed control or sensor
• Commonly used as a safety cutoff in temperature-control circuits
• Can resolve symptoms like persistent overheating, failure to stop heating, or temperature-related shutdowns

• One fixed thermostat (single unit)

• Disconnect power before inspecting or replacing the thermostat to avoid shock or damage
• Handle gently; avoid bending terminals or stressing sensing elements

This rinse aid sensor detects the presence/level of rinse aid and signals the dishwasher control so the dispenser and cycle logic respond correctly. Replaces a failed sensor to restore proper rinse-aid detection. What it does

• Acts as a reed-style sensor that notifies the control when rinse aid is present
• Helps the dispenser and control board make rinse-aid–related decisions
• Commonly replaced when rinse-aid indicators fail or rinse-aid detection errors occur
• Small, low-voltage sensing device used in the dishwasher dispenser area

• One rinse aid sensor (reed switch)

• Disconnect power to the appliance before starting any service
• Access may require removing the door inner panel or dispenser assembly; follow the service manual
• Handle gently and avoid bending the sensor leads; ensure secure electrical connections

Dryer not heating or leaving clothes damp? This thermostat with sensing cable regulates temperature and prevents overheating. Easy DIY repair part.

Range showing F3 or F10 error code? This safety thermostat prevents overheating by cutting power when temperatures exceed safe limits. Moderate DIY repair.

This thermoprotector switch is a safety device that monitors oven temperature and cuts power to the heating element if the oven exceeds safe operating temperatures. It helps prevent overheating and potential damage to the oven's components. Replace this switch if your oven shuts off unexpectedly, fails to heat properly, or if you suspect the thermal safety cutoff is no longer functioning correctly.

This sensor detects moisture levels inside the microwave cavity during cooking and communicates with the control board to adjust cook times automatically. It is a key component for auto-cook and sensor-reheat functions. Replace this sensor if the microwave fails to properly detect doneness, overcooks or undercooks food on sensor settings, or displays a sensor error code.

If your microwave won't heat or overheats, the thermostat may be faulty. This temperature control part regulates heating cycles for safe operation.

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

Washer not heating or cooling properly? This thermistor temperature sensor assembly measures internal temps and sends readings to the control board.

If your air conditioner won't start or shuts down unexpectedly, a failed compressor overload protector is often the cause. This simple swap restores starts.

This thermistor is the refrigerator temperature sensor that helps the control board monitor and regulate cooling. Replacing a faulty sensor restores accurate temperature readings and consistent cooling performance. What it does:

• Measures internal refrigerator/freezer temperature and sends readings to the control board
• Helps the control board adjust compressor and fan operation for stable temperatures
• Can cause incorrect temperature display or uneven cooling when it fails
• Linked to excessive running, frequent defrost cycles, or poor cooling performance

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the sensor and wiring harness carefully; avoid kinking or damaging the lead
• Ensure the connector is fully seated and any mounting clip or bracket is secured
• Some panel removal may be required; follow for access and reassembly