Switch

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

This relay change kit replaces the failed relay assembly that controls motor or compressor power, restoring proper electrical switching for normal operation. Use this kit to replace a worn or intermittently working relay with an exact-fit factory component. What it does

• Switches power to the motor/compressor when the appliance calls for it
• Restores reliable start and run signals when a relay has failed or sticks
• Addresses symptoms like clicking on start, no motor/compressor operation, or intermittent runs
• Helps prevent damage from repeated failed start attempts

• One relay change kit

• Disconnect power before servicing to avoid shock or damage
• Replace only with the exact OEM relay kit for safe, reliable operation
• Verify wiring and connectors are secure and undamaged before restoring power

Fixes burner that won't shut off or heat properly. This infinite switch controls cooktop element temperature. Moderately easy DIY repair.

Burner won't heat or stays on high? This cooktop infinite switch controls element temperature settings. Moderate DIY repair taking 30-45 minutes.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage

Range burner won't heat or stuck on high? This infinite switch controls surface element temperature settings. Restores precise heat control to cooktop.

A push-button switch that restores user control functions by completing or breaking electrical circuits. Replaces a worn or failed control switch to help restore normal operation and user input response. What it does:

• Acts as the user-operated control input to start or stop a function when pressed
• Opens or closes the electrical circuit that enables the associated control or feature
• Common symptom: unresponsive controls or functions that do not start when buttons are pressed
• May cause intermittent operation or no response if contacts are worn or corroded

• One replacement push-button switch

• Disconnect power to the appliance before attempting any service
• Use appropriate tools and basic electrical safety; avoid bending terminals or forcing the new part into place

If your cooktop burner won't heat, stays on one setting, or heats erratically, this control switch regulates power to restore proper temperature selection.

This control switch is the user-facing rotary selector that lets the appliance select cycles and settings. It restores clear, tactile control so the unit responds correctly when you turn the knob. What it does:

• Selects operating cycles and settings when the knob is turned
• Routes electrical signals from the control panel to the selected function
• Commonly replaced when settings do not change or the control feels loose/slips
• Resolves intermittent or unresponsive cycle selection and erratic behavior

• Disconnect power before attempting any repair to avoid electrical shock
• Accessible from the control panel; remove trim or console as needed per your model's service instructions
• Test function after reassembly; do not force the selector or use excessive torque

Burner won't heat or stays on high? This infinite switch controls top burner temperature settings. Restores precise heat adjustment to your cooktop.

Range burner not heating or stuck on high? This infinite switch controls surface element temperature. Common fix for unresponsive cooktop controls.