Kenmore / Sears Parts

First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

• Won't start

Ordered a new thermal fuse from your website last week and installed it three days ago. This is the second fuse in one year that needed to be replaced. The dishwasher was purchased new in 2012. Relatively easy to replace. Your website had a you tube video that showed how to replace it. Power came back on the control panel, but the start button (not a button, but a touch screen) would not work. This is the second time in two years that the control panel had to be replaced because the start... Read more

Replaced with no problem. Exact fit. Less than 5 minutes. I will order from your company again. Arrived on scheduled date. Read more

Replaced the door latch/lock assembly. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

• Noisy

Using appliancepartspros.com site took washer apart to diagnose bad clutch. The clutch was bad but once inside I noticed grease everywhere and after a quick online chat with rep. determined gear case was leaking and needed replacement. Replaced clutch & gear case. Followed video tutorial and took a little more than 30 minutes start to finish for me - I have no experience. The most difficult part for me was actually just getting the retainer ring (little wire) to secure clutch in place-took... Read more

• Oven not heating evenly
• Oven is too hot
• Little to no heat when baking
• Element will not heat

Ordered spare part that actually fit my oven. Arrived in three days from next state over. Unplugged power cord, removed racks, used 1/4" socket on ratchet with 6 inch extension to remove two sheet metal screws at lower back of oven. Pulled old element out 2 inches then tilted front of element up 45 degrees for spade connectors to clear holes at back of oven. Once clear, pulled element forward until the white #16 wires pulled through the openings in the oven (inside at the back). By hand, gently... Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

Ordered a new filter. Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

• Will not drain

Replaced the solenoid and bracket assembly Read more

• Will not drain

Step 1. Turn off water and power to dishwasher. Ours does not have any easy plug under the sink, so this was our first red flag that this was going to be complicated. Step 2. Unscrew dishwasher from cabinet brackets. 3. Dismantle the hardwired box underneath-2 wires, 1 ground. Step 3. Dishwasher would not come out of the cabinet far enough to remove. Step 4. Have a good cry because it's been over an hour now and the directions said this would be easy. Step 5. Use a wrench to detach the water... Read more

I had an authorized Whirlpool service tech come to look at problem diagnosed problem as water inlet valve leaking ordered the part. After 11 days I was told part was on backorder from Whirlpool. I ordered the part from you and received the next day and I installed it in approximately 20 minutes. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more