Lg Parts

This vegetable tray assembly provides the stable bottom surface for the refrigerator crisper so produce stays organized and contained. Replace a cracked, warped or missing tray to restore proper storage and prevent items from shifting. What it does:

• Serves as the bottom shelf for the vegetable/crisper compartment to keep produce contained and organized
• Restores support when the original tray is cracked, broken or missing
• Helps prevent items from sliding into the drawer gap or contacting interior components
• Keeps the crisper area cleaner and easier to wipe down

• Typically installs by sliding into the crisper/drawer rails; check orientation before seating
• Handle carefully — plastic or glass trays can chip or crack during handling
• Follow safety precautions

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

This replacement control knob restores smooth, reliable operation of a range surface burner. It mounts on the valve stem so you can turn the burner on/off and select heat levels with a secure grip. What it does:

• Attaches to the burner valve stem to control flame/heat
• Replaces knobs that are cracked, stripped, wobbly, or missing
• Helps prevent slipping or free-spinning on the stem
• Common symptoms: knob won't turn, falls off, or is melted/damaged

• Includes 1 knob assembly

• Turn all burners off, allow the surface to cool, and disconnect power before beginning
• Pull the old knob straight off the stem; no tools are usually required
• Align the flat side of the stem with the new knob and press firmly until seated
• If it won't seat, stop and inspect the stem for damage or misalignment

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This ice bucket holds and stores ice produced by the refrigerator's icemaker, keeping cubes contained and easy to access. It replaces a cracked, damaged or missing bucket so ice can be collected without spilling into the freezer. What it does:

• Collects and stores ice produced by the icemaker until you remove or dispense it
• Keeps ice contained to prevent loose cubes from scattering in the freezer
• Restores proper seating for the ice delivery area to reduce jams or blockages
• Useful when the original bucket is cracked, warped, or missing

• One ice bucket

• Unplug the refrigerator or switch the icemaker to OFF before replacing the bucket
• Remove all loose ice and the old bucket before installing the new one
• Slide the new bucket into place until it seats securely; do not force
• Rinse the new bucket with clean water before first use

Replacement inlet valve assembly that controls water entering the washer so cycles fill properly and the appliance runs as expected. Installs at the water inlet to restore proper filling and stop leaks caused by a faulty valve. What it does:

• Opens and closes the water path into the washer to allow correct fill levels during wash cycles.
• Stops or reduces water flow when the valve is closed to prevent overfilling.
• Common symptom fixes: washer won't fill, intermittent filling, continuous filling, or water leaking at the inlet connection.
• Works with the appliance's inlet hose connections and electrical solenoid controls.

• Disconnect power and turn off the home's water supply before starting any repair.
• Remove the access panel, disconnect inlet hoses and electrical connectors, then replace the valve with the correct orientation and seals.
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks.

Restore reliable operation with this power control board assembly. It regulates and distributes incoming power to the appliance's circuits and components so the unit powers up consistently and runs as designed when the original board has failed.

• Regulates and stabilizes power delivered to control and load circuits
• Switches power to motors, heaters, fans, and other components via onboard relays
• Provides low-voltage supply for control electronics
• Typical failure symptoms: no power, unresponsive controls, intermittent shutdowns, repeated blown fuse, or visible board damage

• Disconnect power before servicing; capacitors can retain a charge—allow time to discharge and use proper precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board to maintain orientation
• Inspect wiring, fuses, and downstream components for shorts before restoring power to protect the new board

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.

The door boot gasket seals the opening between your front-load washer's door and outer tub, keeping wash water contained. Replace it if the boot is torn, deformed, or heavily mildewed to restore a reliable, watertight seal.

• Forms a watertight seal between the outer tub and door opening
• Prevents leaks from the front of the washer during wash and spin
• Flexible design maintains the seal as the drum moves
• Common failure signs: water on the floor at the front, dripping at the door, visible rips/cracks, or the boot pulling loose

• Unplug the washer and turn off water supply; wear gloves to avoid sharp edges
• Access the boot by removing panels as required for your model; note hose positions and alignment
• Release the outer and inner retaining clamps/springs and remove the old gasket
• Seat the new gasket evenly, align indexing features/ports, reinstall clamps securely, and run a quick test for leaks

This is the glass turntable tray for a microwave. It provides a stable, food-safe surface and rotates with the turntable system to help heat food evenly.

• Holds dishes securely while the microwave runs and rotates for uniform heating
• Replaces a cracked, chipped, or missing glass plate
• Common symptoms: tray wobbles, won't rotate properly, uneven heating, or visible damage to the plate
• Designed to fit the microwave's turntable coupler and support for smooth operation

• Unplug the microwave (or open the door to stop operation) and let the tray cool before handling
• Remove the old tray; align the new tray's center with the turntable coupler
• Ensure it sits flat and spins freely by hand before use
• Do not overtighten or force—tray should rest on the support/rollers

The Crisper Drawer Assembly is an OEM component specifically designed for LG French door refrigerators equipped with bottom-mounted crisper drawers. This assembly provides organized storage for fruits and vegetables.

Causes of a bad crisper drawer assembly can include broken roller glides preventing smooth operation over years of use, cracked or punctured liners allowing air exchange with fridge interior, and damaged humidity control features like crispers.

Symptoms of a bad crisper drawer assembly include:

• Produce drying out faster than expected  
• Difficulty fully closing or opening the drawer
• Drawer unable to be securely held in closed position
• Bowing or warping reducing usable storage space

Replace yours today with this genuine OEM LG assembly to optimize the storage and preservation of perishables. This replacement part is also compatible with Whirlpool, Maytag, and KitchenAid models for factory performance and design.

Color: Stainless

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location