Lg Parts

The Locker Assembly is an OEM component specifically designed for LG electric dryers. Found behind the dryer door, this assembly houses door-locking mechanics. 

Causes of a bad locker can include wear and tear over time, damage due to impact, or unintentional stress on components.

Symptoms of a faulty locker assembly include:

• The dryer door not latching securely in the closed position  
• Gaps or air leaks are visible around the door seal when running
• The door is unable to stay shut on its weight  
• Loud clicking or grinding noises from the door area

This OEM LG part is also compatible with some Kenmore models.

This is the small trim cap that snaps over the end of a refrigerator door handle. It finishes the handle, covers the mounting hardware, and helps keep the handle secure and looking clean.

• Covers exposed door-handle screws and mounting points
• Restores a finished appearance if the original cap is missing or damaged
• May help reduce handle looseness if the old cap no longer held properly
• Common symptoms: missing end cover, visible handle screws, loose or rattling handle

• Unplug the appliance before starting and open the door for access
• Remove the old cap by gently prying at the seam; avoid scratching the door finish
• Align the new cap with the handle end and press until it snaps fully into place
• If required, tighten handle mounting screws before installing the cap

Replace a damaged or stripped leveling foot with this leg assembly. It supports the appliance and adjusts for height so you can level it on uneven floors, restoring stability and helping reduce vibration, noise, and movement. What it does:

• Provides adjustable height to properly level the appliance
• Supports the cabinet/frame to keep all corners in firm contact with the floor
• Helps reduce rocking, walking, vibration, and rattling noises
• Fixes: appliance wobbles or is unstable; foot is cracked/missing; threads are stripped; cannot be leveled

• One leg assembly

• Disconnect power and, if applicable, turn off the water supply before servicing
• Carefully tilt or raise the appliance; protect the floor from scratches
• Unscrew the old leg; thread the new leg in by hand and adjust height to level
• Ensure all feet contact the floor firmly and the unit is stable before use

This door hinge bracket mounts the hinge to the washer's front cabinet, keeping the door aligned so it closes and seals properly. A bent or broken bracket can lead to door sagging, poor latching, or leaks at the door.

• Secures the door hinge to the washer's front panel/cabinet
• Supports door weight to maintain alignment
• Helps preserve proper door-to-gasket contact for sealing
• Typical symptoms: door sags or rubs, won't close/latch, or water leaks at the door

• Disconnect power and shut off water before servicing.
• Support the door before removing hinge/bracket screws to prevent strain.
• Transfer the hinge to the new bracket and reinstall using existing hardware.
• Align the door and ensure latch engagement and gasket seal before fully tightening.

This ice bucket holds and stores ice produced by the refrigerator's icemaker, keeping cubes contained and easy to access. It replaces a cracked, damaged or missing bucket so ice can be collected without spilling into the freezer. What it does:

• Collects and stores ice produced by the icemaker until you remove or dispense it
• Keeps ice contained to prevent loose cubes from scattering in the freezer
• Restores proper seating for the ice delivery area to reduce jams or blockages
• Useful when the original bucket is cracked, warped, or missing

• One ice bucket

• Unplug the refrigerator or switch the icemaker to OFF before replacing the bucket
• Remove all loose ice and the old bucket before installing the new one
• Slide the new bucket into place until it seats securely; do not force
• Rinse the new bucket with clean water before first use

Replacement inlet valve assembly that controls water entering the washer so cycles fill properly and the appliance runs as expected. Installs at the water inlet to restore proper filling and stop leaks caused by a faulty valve. What it does:

• Opens and closes the water path into the washer to allow correct fill levels during wash cycles.
• Stops or reduces water flow when the valve is closed to prevent overfilling.
• Common symptom fixes: washer won't fill, intermittent filling, continuous filling, or water leaking at the inlet connection.
• Works with the appliance's inlet hose connections and electrical solenoid controls.

• Disconnect power and turn off the home's water supply before starting any repair.
• Remove the access panel, disconnect inlet hoses and electrical connectors, then replace the valve with the correct orientation and seals.
• After installation, restore water and power, run a short fill cycle, and check all connections for leaks.

Restore reliable operation with this power control board assembly. It regulates and distributes incoming power to the appliance's circuits and components so the unit powers up consistently and runs as designed when the original board has failed.

• Regulates and stabilizes power delivered to control and load circuits
• Switches power to motors, heaters, fans, and other components via onboard relays
• Provides low-voltage supply for control electronics
• Typical failure symptoms: no power, unresponsive controls, intermittent shutdowns, repeated blown fuse, or visible board damage

• Disconnect power before servicing; capacitors can retain a charge—allow time to discharge and use proper precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board to maintain orientation
• Inspect wiring, fuses, and downstream components for shorts before restoring power to protect the new board

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.

The door boot gasket seals the opening between your front-load washer's door and outer tub, keeping wash water contained. Replace it if the boot is torn, deformed, or heavily mildewed to restore a reliable, watertight seal.

• Forms a watertight seal between the outer tub and door opening
• Prevents leaks from the front of the washer during wash and spin
• Flexible design maintains the seal as the drum moves
• Common failure signs: water on the floor at the front, dripping at the door, visible rips/cracks, or the boot pulling loose

• Unplug the washer and turn off water supply; wear gloves to avoid sharp edges
• Access the boot by removing panels as required for your model; note hose positions and alignment
• Release the outer and inner retaining clamps/springs and remove the old gasket
• Seat the new gasket evenly, align indexing features/ports, reinstall clamps securely, and run a quick test for leaks

This is the glass turntable tray for a microwave. It provides a stable, food-safe surface and rotates with the turntable system to help heat food evenly.

• Holds dishes securely while the microwave runs and rotates for uniform heating
• Replaces a cracked, chipped, or missing glass plate
• Common symptoms: tray wobbles, won't rotate properly, uneven heating, or visible damage to the plate
• Designed to fit the microwave's turntable coupler and support for smooth operation

• Unplug the microwave (or open the door to stop operation) and let the tray cool before handling
• Remove the old tray; align the new tray's center with the turntable coupler
• Ensure it sits flat and spins freely by hand before use
• Do not overtighten or force—tray should rest on the support/rollers

The Crisper Drawer Assembly is an OEM component specifically designed for LG French door refrigerators equipped with bottom-mounted crisper drawers. This assembly provides organized storage for fruits and vegetables.

Causes of a bad crisper drawer assembly can include broken roller glides preventing smooth operation over years of use, cracked or punctured liners allowing air exchange with fridge interior, and damaged humidity control features like crispers.

Symptoms of a bad crisper drawer assembly include:

• Produce drying out faster than expected  
• Difficulty fully closing or opening the drawer
• Drawer unable to be securely held in closed position
• Bowing or warping reducing usable storage space

Replace yours today with this genuine OEM LG assembly to optimize the storage and preservation of perishables. This replacement part is also compatible with Whirlpool, Maytag, and KitchenAid models for factory performance and design.

Color: Stainless

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This factory kit reconfigures your dryer's exhaust to exit from the side or bottom instead of the rear. It's ideal for tight installations or when the wall vent location requires an alternate exhaust path. What it does:

• Redirects the exhaust outlet to the left, right, or bottom on compatible models (orientation varies by model)
• Enables installation in closets or shallow spaces where rear venting isn't practical
• Replaces missing or damaged side/bottom vent hardware
• Helps maintain a proper metal exhaust path when relocating the dryer

• One side vent kit

• Disconnect electrical power and shut off gas supply (if applicable) before starting
• Follow the model-specific instructions supplied with the kit or in your dryer's installation manual
• Use rigid or semi-rigid metal ducting only; avoid plastic or vinyl
• After assembly, check for secure connections, no kinks, and unobstructed airflow

This nozzle connector links a water hose to the washer's nozzle/dispenser assembly, creating a tight, leak-resistant connection. Replacing a worn connector helps stop leaks and restores consistent water flow during fill and spray functions. What it does:

• Couples the hose to the nozzle/dispenser assembly and maintains a watertight seal
• Directs water into the dispenser or tub as designed
• Typical failure symptoms: leaks near the top panel or dispenser, loose hose, weak or erratic spray/fill
• Cracking, hardening, or deformation can lead to drips and connection issues

• 1 nozzle connector

• Disconnect power and shut off water supplies before servicing
• Remove the top cover to access the dispenser/nozzle area; protect the work area with a towel
• Release hose clamps, seat the hose fully on the new connector, and secure clamps firmly
• Run a brief fill/rinse to check for leaks before reassembly