Maytag Parts

I called to ask about the correct gasket for the door. As VERY helpful lady suggested that it was probably a split arm spray. She was absolutely correct. I have used you web site for parts in the past and will always make it my first stop when ordering appliance parts. Read more

• Ice maker not making ice

After researching a number of sites for a diagnosis I tended to think the culprit was going to be the ice maker thermostat. Checking pricing and availability of the thermostat prices were very close at $40 BUT wait now you have to but the thermo mastic at another $35-$40. And after some continued research the factory ice maker in a $3000 msrp 4 door refrigerator was/is known to be defective long after warranty period expires. So it only made intelligent sense to buy the entire icemaker at a... Read more

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

All you need is a nut driver. The end cap is attached to the side of the refrigerator cabinet with two long screws. Once you remove them, you should slide the end cap towards you. It will release the internal clip that holds the front of the end cap. You should then unscrew the metal slider from the end cap. Assembly of the new end cap is the reverse. You should first attach the metal slider to the new end cap. Attaching the new end cap to side of the refrigerator cabinet is a little tricky.... Read more

I used the Appliance Parts Pros d.i.y. video to get some oversight on the repair; ordered the parts (heating element, Hi-Limit T-stat and Dryer Thermal Cut-Off kit). I unplugged the electric; disconnected the exhaust duct; moved the clothes dryer so that I could remove the back sheet metal panel. The electrical connection at the heater "Stacon" terminal was corroded and broken - an open circuit. This had happen about 10 years before and I was familiar with this problem. After removing the... Read more

While looking for parts thru AppliancePartsPros.com, I found a diagram with my refrig model # for the door shelf bin. It was a perfect match. Prior to that I've spent countless hours searching and became very frustrated. The diagrams and videos were very helpful. Thank you, KShigeta Read more

First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable... Read more

This was my first attempt, ever, to repair a washing machine. After some internet research on the problems, I was able to determine that the shaft seal on the gearcase probably was leaking water into the gearcase with each use. No water was ever found on the floor, but when I turned the washer over to inspect the gearcase, I found a black, oily residue on the outside of it along with the same residue on the pulleys, the belt and the motor. I ordered a new gearcase, shift actuator, splutch... Read more

I watched videos on the disassembly of my dryer model, and got the model number hiding on the upper dryer door jamb. After calling AppliancePartsPros.com for help, then ordered parts with the help of APP. It took almost a full day to disassemble the dryer I have, as it is a little more complicated than some models, and I went very slowly on purpose to not lose screws, or break plastic parts. Getting the wiring harness apart was the hardest thing to do, as the screwdriver shown in the video... Read more

I replaced the icemaker. It was fairly easy, with the most difficult part being access to the icemaker in the bottom freezer. I loosened two screws, removed one additional screw, disconnected the wiring and removed the old icemaker. I mounted the wiring harness and ice level sensor arm from the old unit onto the new icemaker and installed it with no problems. I wish I'd done this months ago instead of repeatedly attempting to repair the old icemaker. Read more

• Too hot

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Leaks water
• Leaking
• Will not drain
• Fills and drains at the same time

With much trepidation, I Googled leaking washing machines and deduced that our problem was likely (but not certain) that we needed to replace the direct drive washer pump. After viewing the AppliancePartsPros video, I decided that ordering the $30 part was worth the risk (vs a $120 plus service call). The pump arrived w/in 2 days and my wife and I experienced an enjoyable bonding experience installing it :). But it's now working great and there is no leak. ... Kudos to AppliancePartsPros for a... Read more

I replaced the adjusters on both sides (since two rollers broke off on one and one broke off on the other). Replacement was easy, just remember to keep the clips from the original adjusters. Take the clips off, remove the adjuster, replace with the new adjuster, and replace the clips. The new adjuster comes with the rollers already attached so no need to keep the ones from when plastic axle broke on the original adjusters. Read more

I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more

Replaced suspension springs/rods and all associated bushings in the kit. Read more

• Will not tumble
• Noisy
• Shuts off too soon

My 12 year old Kenmore dryer problem started about 3 years ago with the motor just stopping. My thing was: I would turn it off and turn the drum by hand about halfway around and it would work again. Last month, my wife said it stopped again and its making a loud noise, but when I did "my thing" it still made a loud squealing noise (like I was killing a mouse). I made time to work on it the next day, I took it apart, using the video instructions from AppliancePartsPros, I removed the top,... Read more