Washer Gasket & Seal

Replaced the seal. Read more

With the basket out of the dishwasher, the plastic parts basically snap on and off... popped the broken parts off and the new parts on. The 2 wheel and mount assemblies were a little more complicated. The video on the website advises to disconnect the supply line and drain line... I didn't have to do this. I just pulled the dishwasher out of its cabinet a little over a foot and removed the 2 screws holding each assembly in place and removed them. The previous gaskets (2 PER ASSEMBLY)... Read more

We replaced the Tub Seal. Read more

Took the machine apart and found 2 leaks. Drum was leaking and a hose had a hole in it . Read more

Replaced with new bellows from appliance parts pros. Read more

Replaced the bellow without having to remove any of the panels. Was able to make the repair from the front of the machine by just removing the 2 clamps that hold the bellow seal in place. Read more

I sat an watched a wash cycle. When it came to drain cycle I could hear the pump making a grinding noise! Door bellow seal leaked too. I ordered new pump and housing,new door bellows seal. The clearance of the pump impeller and housing are real important. I have jet Skies and I knew it is an issue. Watched the video on the repair. Gave me all the instructions to take it apart. One thing it did not show. Lube the new seal mating surface with laundry detergent. It went right on. I have never... Read more

Background - Wife and I are 78 years old. Since there is no budget for new or repair we did it ourselves. I have COPD and could no have done it without her help. Watch you tube examples and followed them. replaced the coupler motor to trans and since we were there replaced the clutch and agitator kit. Also replaced hoses with new stainless hoses. Just tested and everything seems to work as new. Not bad for a machine 12-15 years old. I looked at new ones but the EPA has turned them into... Read more

After researching the Internet, I thought the drainage hoses were my problem. First I changed both drainage hoses. That didn’t solve the problem. I had to look for another area that was causing water to drip into the pan. I found water leaking from behind the brake assembly. Since I didn’t get an oE error code, I eliminated the brake assembly as causing my problem. I ordered a brake gasket and cover. Once I got it properly installed, problem solved! Read more

This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more

Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more

Replaced the boot gasket with help from the online tutorial, took me about an hour but I considered that very reasonable. I think this project could be handled by just about anyone who is remotely handy. Read more

I ordered the parts. Watched a youtube video. and tore it apart. Knocked out the bearings and seal, cleaned it up and popped the bearings and seal back in. Put it back together, and wallaa...no more jet engine. Read more

Replaced the seal. Read more

I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more