Washer Dryer Combo Parts

Dryer not heating properly or overheating? This cycling thermostat regulates temperature by cycling the heating element on and off. Moderate DIY repair.

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Interior drum baffle that lifts and tumbles clothes during the drying cycle. Replace if cracked, broken, melted, or missing to restore proper tumbling.

Right-side door hinge for laundry centers. Replaces worn or damaged pivot point to restore proper door alignment and prevent sagging or gaps in the seal.

This is a rubber lip seal that fits around the upper portion of the washer's basket drive tube, preventing water from leaking past the shaft and into the transmission or bearings below. It creates a watertight barrier between the wash tub and the drive mechanism. Replace this seal if you notice water leaking from beneath the washer tub, hear grinding noises during the spin cycle, or find oil residue under the machine.

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Plastic socket that holds the suspension rod ball in your washer. Replace if worn, cracked, or deformed to restore proper tub support and alignment.

Secures the drain hose in place to prevent kinks, rubbing, and leaks. Replace if hose sags or moves during cycles. Verify fit with your model number.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

This is a Belleville-style spring steel washer used in the suspension or counterweight mounting system of a washing machine. It acts as a spacer and provides spring tension to help absorb vibration during the spin cycle. Replace this washer if the machine vibrates excessively, makes banging noises, or if the original washer is flattened, cracked, or missing.

Hex washer head screw secures panels, brackets, and drum assemblies in washers. Replace rusted, stripped, or missing screws to prevent rattling.

Ceramic dryer heating element housing insulator.

This terminal block provides the electrical connection point where the power cord wires attach to the dryer's internal wiring. It is typically mounted on the rear of the dryer near the power cord entry point. Replace this part if you notice burn marks, melted plastic, loose wire connections, or if the dryer is not receiving power properly.

This round on/off switch replaces the worn or broken power control on compatible appliances, restoring reliable on/off operation and user control at the front panel. Designed to match OEM fit and function for direct replacement. What it does:

• Provides a simple on/off user control for the appliance's power circuit
• Re-establishes consistent electrical contact when the original switch fails
• Commonly fixes symptoms like no power from the control location, intermittent power, or a switch that won't stay on
• Operates as the primary user-actuated power control for the associated circuit

• One round on/off switch

• Disconnect power to the appliance before testing or replacing the switch to avoid shock
• Verify correct wiring location and connectors before removing the old switch; transfer any wiring harness or connectors exactly
• Handle with care to avoid damage to the switch actuator or mounting tabs