Washer Dryer Combo Parts

This replacement shield is a direct-fit protective cover that restores the appliance's factory protection for internal components. It prevents contact with sensitive parts and helps keep wiring and controls clear of debris. What it does:

• Protects wiring, controls and nearby components from heat, moisture and debris.
• Restores the original barrier that helps prevent accidental contact with moving or hot parts.
• Replaces cracked, broken or missing shields that can lead to rattling, exposed components or interference.
• Helps maintain appliance safety and quiet operation when installed correctly.

• One replacement shield

• Always disconnect power to the appliance before starting any repair.
• Handle replacement shield carefully — edges may be sharp; use gloves and basic hand tools.
• Retain and reuse original fasteners unless new hardware is specified; ensure shield is properly seated and secured.
• Do not operate the appliance with shields or covers missing.

This factory replacement screw secures panels, brackets, or trim on your appliance so parts stay tight and aligned. Swap in a new screw when one is missing or stripped to restore a solid, rattle-free fit.

• Fastens compatible panels, brackets, handles, or internal hardware
• Helps maintain proper alignment and stability
• Common fix for loose or wobbly handles/trim, rattling noises, or missing hardware
• Replace if threads are stripped, head is damaged, or corrosion is present

• Disconnect power before servicing; wear cut-resistant gloves
• Use the correct screwdriver or nut driver to avoid stripping
• Start threads by hand to prevent cross-threading
• Tighten until snug; do not overtighten

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

This safety thermostat is a temperature-limiting switch that helps protect your refrigerator/freezer by opening the circuit if temperatures reach an unsafe level, preventing damage to components and reducing fire risk. What it does:

• Monitors internal temperature and interrupts power when the preset limit is exceeded
• Prevents overheating of heating elements or compressors in defrost and refrigeration circuits
• Helps stop continuous run or cycling caused by thermal faults
• May be used as part of the fridge/freezer safety/limit control system

• Disconnect power to the appliance before inspecting or replacing the thermostat
• Handle carefully and avoid kinking or crushing any sensing element or capillary tube
• Verify function and wiring location against your model's service manual or wiring diagram

This cover protects the appliance's fuse and terminal area, keeping electrical connections insulated and reducing the risk of shorting or arcing. A simple replacement restores the protective barrier over the fuse compartment. What it does:

• Shields the fuse and terminal block from debris and accidental contact
• Helps prevent electrical shorts or arcing at the fuse/terminal area
• Keeps the fuse securely positioned in its holder
• Restores the appliance's intended insulation and safety for the electrical connection

• One fuse terminal cover

• Disconnect all power to the appliance before accessing the fuse or terminal area
• Remove any mounting screws or clips holding the old cover; replace with the new cover in the same orientation
• Inspect the fuse and terminal connections for damage before reassembly; replace any damaged components as needed
• Do not operate the appliance with the fuse or terminals exposed

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

Restore a proper seal at the top of your washer's tub with this tub cover assembly. It contains water and suds, reduces splashing, and provides a smooth rim to protect garments during wash and spin. Also called a tub ring.

• Seals the top of the outer tub to keep water and suds contained during operation
• Provides a smooth basket opening to help prevent fabric snagging
• Helps maintain stable operation; a cracked or loose cover can rub, vibrate, or leak
• Common symptoms: water or suds at the top of the tub, excessive splashing, visible cracks or broken tabs

• Disconnect power and turn off water supply before servicing
• Lift/remove the washer top to access the tub area; release clips/fasteners holding the old cover
• Clean the tub lip and transfer any reusable components from the old cover if applicable
• Seat the new cover evenly and secure all tabs/clamps; run a leak check

A replacement cycling thermostat that helps regulate dryer temperature and prevent overheating by cycling the heater on and off as needed. Restores temperature control for safer, more consistent drying. What it does

• Opens and closes to cycle the heating element, maintaining proper operating temperature.
• Helps prevent excessive heat build-up that can cause clothes damage or dryer shutdowns.
• Common fix for dryers that run too hot, have uneven drying, or won't maintain heat.
• Works with the dryer's existing temperature control system to stabilize cycles.

• One cycling thermostat

• Disconnect power before accessing or replacing the thermostat to avoid shock.
• This part mounts inside the dryer cabinet near the heating assembly.
• Handle the thermostat carefully and reconnect wires to the correct terminals.
• Test the dryer on a short cycle after install and monitor temperature; if symptoms persist, check other heating components.

This replacement screw secures appliance panels and components to restore proper fit and reduce movement. It's a simple, direct fix when small fasteners are missing, worn, or stripped and panels sit loose or rattle. What it does:

• Secures trim, panels, or internal components to keep parts aligned
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or damaged screws that prevent proper panel attachment
• Restores a safe, snug fit for covers and access panels

• Disconnect power or fuel supply before accessing the appliance for safety.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent damage to threads or housing.
• Keep small parts away from children and pets during installation.

A white rotary control knob that restores user control of temperature or function settings on compatible appliances. Replaces a cracked, worn, or missing knob to make turning dials easier and safer. What it does

• Replaces a damaged or missing dial so controls can be selected and adjusted smoothly.
• Fits splined control shafts to transmit user input to the switch or timer.
• Common symptom fix: knob slips, spins freely, is cracked, or does not engage the shaft.
• Works for front-panel or console-mounted rotary controls on ranges, ovens, or similar appliances.

• Disconnect power to the appliance before servicing to avoid electric shock.
• Align the knob's internal spline with the control shaft; push straight on until seated.
• Do not force the knob; inspect the control shaft and inner spline for damage before installing.

This clip is a small plastic retainer designed to secure trim and lightweight panels so they stay in place and reduce rattling or gaps. It restores proper fit and helps keep parts aligned for a finished look. What it does:

• Secures trim pieces, panels, or grill components to the appliance frame
• Prevents loose or rattling parts that can cause noise or misalignment
• Holds components in correct position so doors and panels close properly
• Replaces worn or broken clips that no longer grip reliably

• Remove power or disconnect the appliance before servicing when applicable
• Clip installs by snapping into pre-existing mounting hole or slot; no special tools usually required
• Inspect mating surfaces and replace any additional damaged fasteners for best fit

This replacement door gasket seals the refrigerator/freezer door to help maintain consistent temperatures and reduce frost buildup. It restores the cabinet seal so the appliance can cool efficiently and run less often. What it does:

• Provides an airtight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and freezer run time caused by leaks
• Can stop common symptoms like warm spots inside the compartment, excessive frost, or frequent compressor cycling
• Fits into the door channel and compresses to form a continuous seal when the door is closed

• Disconnect power to the appliance before starting any repairs
• Remove the old gasket and thoroughly clean the door channel before installing the new gasket
• Press the gasket evenly into the channel, working around the door to ensure a continuous, wrinkle-free seal
• Avoid using sharp tools that could damage the new gasket; allow the gasket to fully seat before checking for leaks

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This replacement dryer timer advances the cycle sequence and lets the dryer move through timed and automatic settings so clothes dry on the selected cycle. Restores selector/timer control when the original timer fails. What it does:

• Controls cycle advancement so the dryer progresses through timed and automatic cycles
• Enables selection of timed and automatic dry settings via the control knob
• Common symptom: dryer won't advance through cycles or stays stuck on a setting
• Needed if the timer knob doesn't respond, the timer won't turn, or cycles do not complete

• Always disconnect power to the dryer before starting any repair
• Access usually requires removing the control panel or console—handle trim and fasteners carefully
• Note wire locations or take a photo before disconnecting harnesses to ensure correct reassembly

The ball joint seat is the plastic socket for the washer's suspension rod ball. It supports the tub and allows smooth pivoting, helping control vibration and noise when the original seat becomes worn, cracked, or deformed.

• Provides a low-friction seat for the suspension rod ball
• Helps stabilize the tub and isolate vibration during wash and spin
• Wear can cause squeaks/creaks, knocking/banging, or a leaning/off-center tub
• Restores proper suspension movement for smoother, quieter operation

• Disconnect power and water supply; wear gloves and eye protection
• Support the tub before releasing spring/rod tension
• Access the suspension support per model; release the rod from the old seat and install the new seat fully into place
• Ensure the ball end is fully seated before reassembly and testing