Washer Dryer Combo Parts

This left-side door hinge restores correct door support and movement so the appliance door opens and closes smoothly. It replaces a worn or bent hinge that can cause sagging, misalignment, or noisy operation. What it does:

• Supports the left side of the appliance door and maintains proper alignment
• Enables smooth, controlled opening and closing of the door
• Replaces a bent or broken hinge that causes door sag or rubbing
• Helps prevent gaps that can affect door sealing or operation

• Disconnect power (or unplug) and remove any panels as instructed by the manufacturer before starting
• Support the door during removal and installation to prevent injury or damage
• Use proper tools and follow the appliance service manual for torque and fastener locations

This Support is a replacement mounting bracket that helps secure the appliance's internal assembly and restore proper alignment for smooth, quiet operation. Use it to replace worn or damaged supports that allow excessive movement. What it does

• Holds and stabilizes internal components to prevent wobbling or shifting during operation
• Helps reduce rattling, grinding, or knocking noises caused by loose supports
• Restores correct alignment to improve part engagement and function
• Prevents premature wear on adjacent parts caused by excess movement

• One Support mounting bracket

• Disconnect power (and gas if applicable) before beginning any repair
• Inspect surrounding fasteners and mounting surfaces; replace any damaged hardware
• Tighten to manufacturer torque specs where available; avoid over-tightening

One per package.

This genuine OEM part is a washer lid. The washer lid is the main piece that covers the washer. Over time, a washer lid can become damaged to the point where it no longer closes securely. If the washer lid is no longer closing all the way or is severely cracked or damaged, it will need to be replaced.To replace this part, start by making sure the washer is unplugged. After it has been powered off, proceed to take a putty knife to lift to release the two retaining clips that secure the washer's main top. Once released, proceed to remove the lid lock assembly wire connector. Fully remove the main top and set it upside down. Release the tension on the lid springs and detach the springs from the main top and hinge bars. Using a Phillips head screwdriver, remove the screws that secure the hinge bars to the lid. Push the hinge bars through the bearings then twist the bars to remove them. This will separate the lid from the main top. Take the new lid and align it with the main top. Insert the hinge bar between the main top and bearing while threading the screws to secure the new top. Reinstall the top panel and connect the wire harness. This replacement part is sourced directly from the manufacturer and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand washers.

This is a complete microwave oven door assembly that restores a damaged or non-sealing door so the oven operates safely and retains heat. Use it to replace a cracked, bent, or otherwise compromised door assembly. What it does

• Replaces the full door structure including the frame and glass panel so the microwave can close and seal properly.
• Restores proper door alignment and latch engagement when the door is bent or won't stay closed.
• Prevents heat and steam from escaping through damaged seals or cracked glass.
• Helps restore normal operation when the oven won't run due to a door that fails to close securely.

• Disconnect power to the appliance before starting any repair.
• Handle glass and the assembled door carefully; use gloves and eye protection to avoid cuts.
• Align hinges and engage the latch fully when mounting; test door operation before use.
• If the door is heavy or awkward, have a second person assist to avoid dropping or damaging the part.

A replacement silicon controlled rectifier (SCR) that restores proper high-current switching for heating or ignition circuits. Replacing a failed SCR helps stop intermittent heating, loss of element power, or erratic control behavior. What it does:

• Switches and regulates high-current power flow to heating, ignition or motor circuits when gated by the appliance control.
• Prevents or causes intermittent/no-heat conditions when failing or shorted.
• Stops erratic cycling or loss of controlled power to the affected circuit.
• Operates as a direct electrical replacement for the factory SCR specified by the appliance manufacturer.

• Disconnect power before servicing; this part is used in high-voltage sections.
• Match part number and orientation exactly; some installations require soldering or secure connector seating.
• Discharge capacitors and observe ESD precautions when handling electronic components.

A replacement tub outlet clamp that secures the drain boot or hose to the washer tub outlet to help prevent leaks and hose separation. Simple, durable hardware designed to restore a secure water-tight connection. What it does:

• Fastens the drain boot or outlet hose to the tub outlet to stop leaks at the connection.
• Keeps the drain hose or boot from slipping off during the wash cycle.
• Restores a tight, stable seal after worn or damaged clamps cause leaking.
• Works with the tub outlet/boot assembly to maintain normal drain flow.

• One tub outlet clamp.

• Disconnect power to the appliance before beginning any repair.
• Turn off water supply and drain any remaining water from the tub to avoid spills.
• Use appropriate pliers or a screwdriver (depending on clamp type) to remove the old clamp and secure the replacement.
• Inspect the boot/hose and tub outlet for damage; replace damaged components as needed for a reliable seal.

This SCR (silicon controlled rectifier) is a replacement power-control semiconductor used in appliance circuits to switch and regulate current. It restores proper control of heater/motor circuits when the original SCR fails. What it does:

• Controls current flow in high-power appliance circuits for timed heating or motor control.
• Replaces a failed SCR that causes intermittent or no power to the controlled component.
• Common symptom: appliance elements or motors do not turn on or cycle correctly.
• Common symptom: visible burn, cracking, or open circuit at the SCR.

• Disconnect power to the appliance before accessing electrical components to avoid shock.
• Handle the SCR carefully to avoid static or mechanical damage; use original mounting and hardware.

This front suspension rod assembly supports and stabilizes the washer tub from the front of the cabinet. Replacing a worn rod helps reduce vibration, banging, and out-of-balance movement so the washer operates more smoothly.

• Supports and balances the tub from the front corner of the cabinet
• Damps vibration and side-to-side movement during wash and spin
• Helps address symptoms like excessive shaking, banging, or the tub leaning forward
• Reduces walking, rattling, or frequent out-of-balance interruptions

• Disconnect power and water; wear gloves and eye protection
• Support the tub before removing the rod—spring is under tension
• Replace one rod at a time and match the upper/lower end orientation
• Ensure both ends are fully seated in their sockets; re-level the washer after reassembly

This 27" basket assembly replaces a damaged or worn dishwasher rack so you can securely load dishes and slide the rack smoothly. It restores stable support for plates, bowls and glassware and improves rack alignment. What it does:

• Provides the main lower/upper dish support surface so items sit securely during wash cycles
• Restores smooth in-and-out rack travel when original basket is bent or worn
• Prevents dishes from shifting or contacting each other due to damaged tines or walls
• Helps reduce clattering, scraping or poor wash coverage caused by a misshapen rack

• One 27" basket assembly as shown

• Disconnect power to the appliance and shut off the water supply before beginning any work
• Remove remaining dishes and carefully lift out the old basket; handle edges and glassware with care
• Align the basket on the rack rails and slide into position; verify rollers/wheels engage the track
• If the basket is large or awkward, have a second person assist to avoid dropping or damaging the part

This hex washer head screw secures appliance components and hardware, helping keep panels and assemblies fastened for safe, reliable operation. Use it to replace missing or damaged screws that allow parts to shift or rattle. What it does:

• Fastens panels, brackets, and component assemblies using a hex washer head for broad bearing surface
• Restores secure fit where stripped, missing, or damaged screws cause loose parts or vibration
• Maintains proper alignment and prevents movement that can lead to noise or additional wear
• Matches the OEM thread and length for a correct fit when replacing the specific factory screw

• Disconnect power to the appliance before beginning any repair
• Use the correct hex driver/socket to avoid stripping the head
• Thread the screw in straight and tighten until snug; avoid overtightening
• Repair or replace the threaded insert or mounting hardware before installing

Hex washer head ,10-32 x 0.375. Ground

This spring clamp secures the refrigerator door bellow to the cabinet, helping hold the bellow in place for a tighter seal and consistent door alignment. A simple replacement that restores proper bellow retention. What it does

• Holds the door bellow tightly to the cabinet or door frame
• Prevents bellow from pulling away or bunching during door use
• Helps maintain a consistent seal to reduce drafts at the door edge
• Works where a worn or damaged clamp allows visible gap or misalignment

• Basic hand tools usually required; inspect surrounding bellow for wear before installing
• Wear gloves and eye protection; spring clamps can snap back during removal/installation
• If clamp is difficult to seat, ensure bellow is properly positioned and not torn
• Replace damaged bellows or additional fasteners to ensure a complete seal

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

Ceramic dryer heating element terminal block.