Washer Dryer Combo Parts

Secures the backsheet to the cabinet, preventing panel gaps and rattling. Replace if clip is broken or panels are loose. Confirm fit with your model number.

Dryer drum shaft that supports the drum and connects to the bearing. Replace if worn, damaged, or causing squeaking noises. Verify fit with your model.

Shipping bolt kit secures the washer drum during transport. Replace missing or lost bolts when moving your washer to prevent damage to the suspension system.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

This is a small rubber or plastic bumper that attaches to the console area of an ice machine. It acts as a cushion to prevent vibration noise and protect surfaces from impact during operation. Replace this bumper if it is cracked, missing, or deteriorated, which can cause rattling sounds or allow the console to shift out of position.

This siphon break kit installs on the washer's drain hose connection to prevent water from siphoning back into the machine during a wash cycle. It acts as a one-way valve that allows water to drain out while stopping reverse flow. Replace this kit if your washer drains water unexpectedly, fills slowly, or if you notice water siphoning back into the tub after it has been pumped out.

Sound dampening pad for washers. Reduces vibration and noise during operation. Replace if worn, cracked, or missing to restore quiet performance.

This 6-foot rubber hose provides a flexible, durable connection for appliance water/drain routing, helping restore proper flow and reduce leaks. Designed as a direct replacement hose where a 6' rubber line is required. What it does:

• Replaces worn, cracked or brittle 6' rubber hose to stop or prevent leaks.
• Restores flexible routing for water supply or drain lines that need a 6-foot rubber connection.
• Helps eliminate kinks and restricted flow caused by damaged hoses.
• Compatible with standard hose clamps or quick-connect fittings used on many appliances.

• Turn off water and power to the appliance before starting any work.
• Inspect fittings and clamps; replace clamps if corroded or damaged for a secure seal.
• Push hose fully onto the fitting and secure with the proper clamp type; test for leaks before returning appliance to service.

This is a plastic hose connector used to attach the washer drain hose to the drain system or laundry center plumbing. It ensures a secure, leak-free connection between the drain hose and the standpipe or drain outlet. Replace this connector if you notice water leaking at the drain hose junction or if the connector is cracked, warped, or no longer holds the hose firmly in place.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

Terminal block mounting screw for dryers and washer dryer combos. Secures the terminal block to the dryer frame. Replace if stripped, missing, or damaged.

This motor and pulley kit replaces a dryer's failed drive motor and pulley assembly to restore drum rotation and normal drying performance. Designed as a direct-fit service kit for compatible GE dryers. What it does:

• Replaces the dryer drive motor and pulley to restore drum tumbling.
• Restores proper belt drive and helps recover normal drying and ventilation.
• Can stop or reduce symptoms like a drum that won't turn, loud grinding, or a dryer that runs but doesn't tumble.
• Designed to work with the dryer's existing belt and mounting hardware when applicable.

• One motor and pulley kit

• Disconnect power to the dryer before starting any repair.
• Basic hand tools are typically required; remove the dryer cabinet or access panel as needed.
• Support the drum while replacing the motor; follow the appliance's service manual for routing the belt and aligning the pulley.

This is an electrical plug connector used in the dryer's wiring system. It provides a secure connection point for internal wiring to ensure proper electrical flow to dryer components. Replace this plug if it is burned, melted, cracked, or if you are experiencing intermittent power issues with the dryer.

Secures the front panel on dryers. Replace if the panel is loose, rattling, or won't stay in place. Confirm fit with your model number before ordering.

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely