Washer Dryer Combo Parts

Hex pan thread screw for washer dryer combo units. Secures panels and components to the frame. Replace missing, stripped, or damaged fasteners.

Protective cap stud cover for washer dryer combo units. Shields electrical or mechanical studs from debris and maintains secure connections. Replace if cracked, broken, or missing.

Fix washer not filling or slow water flow with a new water inlet valve. Controls water entry to your washer. Moderate DIY repair, 30-45 minutes.

Main wire harness for washer dryer combos. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connections are loose.

Size: 8-32 x .312 inch.

This clip secures the lint screen frame to the dryer housing, keeping the lint filter properly seated during operation. It snaps into place to hold the frame firmly so the lint screen does not shift or rattle. Replace this clip if it is broken or missing, which can cause the lint frame to sit loosely or allow the lint screen to move out of position.

This is a small rubber or plastic cup that sits beneath a washer's leveling leg to protect the floor and reduce vibration. It helps keep the machine stable and prevents the legs from scratching or damaging the surface underneath. Replace this pad if it is cracked, compressed, or missing, which can cause the washer to vibrate excessively, walk across the floor, or make loud banging noises during the spin cycle.

Gas conversion orifice for dryers. Converts natural gas units to LP/propane fuel type. Replace if orifice is lost, damaged, or switching fuel sources.

This replacement drum assembly is the rotating cylinder that tumbles laundry in your dryer. Replacing a damaged or out-of-round drum restores smooth, quiet tumbling and helps protect fabrics from snags, scraping, and uneven drying.

• Forms the rotating chamber that holds clothes; driven by the belt and motor to tumble items for drying
• Works with drum seals and lifters/baffles to maintain airflow and separate fabrics for even drying
• Replacing a dented, cracked, or out-of-round drum can resolve thumping, scraping, or rumbling noises
• Addresses sharp seams, loose spots, or rust that can snag/tear clothing or leave marks

• Disconnect power; shut off gas supply for gas models before service
• Remove top/front panels and release belt tension to lift out the old drum; note belt routing
• Compare parts and move over any reusable, model-specific components if required
• Inspect belt, idler pulley, bearings, and felt seals while open; replace if worn

Seals dryer exhaust duct connection to contain airflow and prevent lint entering cabinet. Replace if cracked or loose to restore efficiency. Verify fit.

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Dryer drum baffle installs inside the drum to lift and tumble clothes evenly. Replace when cracked, broken, or missing to restore proper drum function.

Replaces damaged or worn control panel face on laundry centers. Restores front appearance and provides secure mounting for controls. Needed when cracked or broken.

The Top Bearing is an OEM part for GE electric dryers. Located near the top of the drum assembly, it further supports rotational movement during tumbling.

Symptoms of a faulty top bearing include:

• Emergence of grinding or scraping noises from the upper drum area
• Resistance or lack of responsiveness to smooth drum spinning  
• Potential impacts to interconnected spinning components  

As a bearing used repeatedly over time, standard wear from lint and dust accumulation affects function. Impacts can also compromise integrity on occasion. 

Causes typically include normal wear and tear from prolonged rotational cycles. Heavy loads may accelerate deterioration too by adding strain.

This genuine GE replacement bearing restores reliable support at the top of spinning cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryers too, it extends equipment life through dependable bearing operation once installed.

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two