Washer Dryer Combo Parts

The Baffle is an OEM part for GE electric dryers. Located inside the dryer drum, it helps separate clothes and improves air circulation during tumbling cycles. 

To achieve consistent drying times, a dryer relies on balanced airflow penetrating all areas where clothes reside. The baffle creates divisions to ensure air fully surrounds each layer instead of bypassing some areas. Its raised ridges also help tumbling action by preventing clumps of clothes.

Symptoms of a bad baffle include:

• Slow, uneven drying requiring extra cycles  
• Certain areas of clothes remain damp while others over-dry
• Reduced airflow output from the vent due to blockage

Replacing it with the genuine GE baffle plate restores optimized air distribution within the drum. The part is also compatible with some Kenmore dryers that use GE elements.

This retaining clamp secures wiring, hoses, or small assemblies to keep them routed and stable, helping prevent rubbing and vibration that can lead to wear or intermittent issues. Use it to replace a broken or missing clamp. What it does:

• Holds wires, hoses, or tubing in place to prevent contact with moving parts
• Reduces vibration and rattling by keeping components secure
• Prevents chafing that can cause insulation wear or exposed wiring
• Restores proper routing after repairs or part replacement

• Disconnect power (and water if applicable) before accessing internal components
• Use appropriate hand tools; avoid over-tightening which can damage the clamp or secured part
• Inspect surrounding wiring/hoses for damage and replace if needed

This clamp is a small retaining fastener used to secure hoses, tubes or wiring to appliance fittings and keep connections stable during operation. It helps prevent leaks, chafing and loose connections that can cause performance issues. What it does:

• Secures a hose or tube to a barb or fitting to maintain a tight seal
• Prevents hoses and lines from slipping free during use or vibration
• Reduces wear from rubbing or chafing by holding components in place
• Helps stop minor leaks at hose junctions when properly seated

• One clamp (quantity: 1)

• Disconnect power and water supply before servicing the appliance
• Drain or catch any residual water from hoses before removing the old clamp
• Use the correct pliers or screwdriver for the clamp type; avoid over-tightening which can damage hoses
• Inspect adjacent hoses and fittings and replace any worn components while accessible

The Top Bearing is an OEM part for GE electric dryers. Located near the top of the drum assembly, it further supports rotational movement during tumbling.

Symptoms of a faulty top bearing include:

• Emergence of grinding or scraping noises from the upper drum area
• Resistance or lack of responsiveness to smooth drum spinning  
• Potential impacts to interconnected spinning components  

As a bearing used repeatedly over time, standard wear from lint and dust accumulation affects function. Impacts can also compromise integrity on occasion. 

Causes typically include normal wear and tear from prolonged rotational cycles. Heavy loads may accelerate deterioration too by adding strain.

This genuine GE replacement bearing restores reliable support at the top of spinning cycles. Compatible with some Hotpoint, RCA, and select Kenmore dryers too, it extends equipment life through dependable bearing operation once installed.

This lid bumper cushions the lid of your top-load washer as it closes, absorbing impact to reduce slamming noise and protect the top panel's finish. Replace a worn or missing bumper to restore smooth, quiet lid operation. What it does

• Absorbs impact between the lid and cabinet to reduce slamming and vibration noise
• Helps protect the top panel finish from chips and scratches near the lid area
• Restores proper cushioning when the original bumper is missing, cracked, or flattened
• Common symptoms: lid slams or clunks when closing, increased noise, visible missing bumper

• 1 lid bumper

• Disconnect power before servicing
• Open the lid and pull the old bumper straight out of its mounting hole; needle-nose pliers can help if it's stuck
• Clean the hole and surrounding surface for a secure fit
• Press the new bumper fully into the hole until seated flush; for even cushioning, consider replacing both if your model uses two

This front panel assembly replaces a damaged or worn control-panel face to restore the appliance's front appearance and provide a secure mounting surface for controls. It keeps the control area sealed and looking factory-fresh. What it does:

• Replaces the visible front/control panel to cover and protect underlying controls and electronics
• Provides a mounting surface for buttons, knobs, or the touch-control interface
• Helps prevent dirt, grease, and moisture from reaching internal components
• Common repair for cracked, discolored, or broken control-face panels

• One front panel assembly as shown

• Installation requires removing the range/oven console and disconnecting power first — disconnect power at the breaker or unplug the appliance
• Handle panels and clips carefully to avoid damaging trim tabs or painted surfaces
• Use proper fasteners and alignment during reassembly; verify controls and display function before returning the appliance to service
• Label connections and take photos for reference

This right-hand hinge washer cover protects and conceals the hinge area on the washer lid, restoring a finished appearance and preventing dirt or moisture from contacting the hinge assembly. What it does:

• Covers the right-side hinge/washer area to keep debris and moisture out of the hinge assembly
• Helps maintain proper lid alignment and reduces exposed sharp edges
• Restores the washer's cosmetic finish after damage or wear
• Can eliminate rattling or rubbing caused by a missing or broken cover

• One right-hand hinge washer cover

• Disconnect power to the appliance before starting any repair
• Remove the washer lid or access panel per the manufacturer's instructions to reach the hinge area
• Fasten the cover using the original screws/clips; do not force or overtighten plastic tabs
• If other hinge components are damaged or loose, inspect and replace as needed for a safe repair

This replacement power cord restores the electrical connection for compatible Frigidaire appliances so they can safely receive power. Durable insulation and molded ends help ensure a secure, reliable feed to the appliance. What it does

• Provides the main AC power connection between the appliance and the household outlet.
• Replaces damaged, frayed, or burned cords that can cause power loss or unsafe conditions.
• Common symptom: appliance does not power on or loses power intermittently.
• Common symptom: visible cord damage, exposed wires, melting, or frequent tripping of a circuit breaker.

• Always disconnect the appliance from power at the breaker or unplug before installing.
• Inspect the cord routing and strain relief; replace any damaged clamps or covers.
• Tighten terminal connections securely; avoid over-torquing which can damage terminals.

This stop-drain hose routes and drains water from the appliance to the drain or pump, helping prevent standing water and improper drainage. Replaces a worn, cracked, or leaking drain hose to restore proper water flow. What it does

• Channels discharged water from the appliance to the drain/pump assembly.
• Stops leaks caused by split, brittle, or collapsed hose sections.
• Helps restore normal draining when water pools in the tub or cabinet.
• Reduces the chance of water damage from a failed hose connection.

• Disconnect power and shut off the water supply before beginning any work.
• Remove old hose and inspect fittings; replace clamps if corroded or damaged.
• Route hose without sharp bends or kinks and secure with the factory clamps or equivalent.
• After installation, run a short cycle and check all connections for leaks.

This multi-vent plug seals an unused vent opening to stop unwanted airflow and keep the appliance interior protected. It's a direct-fit replacement designed to restore proper venting and help prevent drafts, debris, and pests. What it does:

• Plugs an unused multi-vent opening to prevent air leakage and drafts
• Helps keep dust, lint, and small debris out of the appliance vent path
• Reduces the chance of pest entry through an open vent
• Restores the intended vent configuration after service or part removal

• Disconnect power or gas to the appliance before servicing for safety
• Install by aligning and pressing the plug firmly into the vent opening until seated
• Do not force if resistance is excessive; inspect for obstructions or damage
• Replace damaged parts before installing the plug

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

This replacement cover restores the appliance's exterior finish while protecting internal components from dust and debris. It fits into the cabinet opening to secure and conceal underlying parts for safe, clean operation. What it does:

• Protects internal components and wiring from dust, lint, and accidental contact
• Restores a finished appearance when a panel is cracked, warped, or missing
• Prevents small items from falling into the appliance cavity
• Reduces rattling from loose or missing panels

• One replacement cover

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools (screwdriver) may be required to remove fasteners or retainers
• Align tabs or slots, then secure fasteners without overtightening to avoid cracking

This control panel front is the exterior cover for the appliance's electronic control area, restoring the unit's finished appearance and protecting buttons and displays from dirt and damage. It's a direct-fit cosmetic and protective replacement. What it does:

• Covers and protects the appliance control keypad and display from spills, dust, and wear
• Provides the correct surface for buttons and touch controls to operate properly
• Restores the appliance's original look when the factory panel is cracked, scratched, or discolored
• Helps prevent moisture and debris from reaching internal electronics

• High-level replacement: remove power and access the control housing before swapping panels
• Typical procedure: detach outer trim or bezel, remove fasteners holding the old panel, transfer any mounted buttons or overlays, then secure the new panel
• Use caution around glass, sharp edges, and wiring; avoid forcing connectors

This genuine-style door gasket replaces a worn or damaged refrigerator door seal to restore a tight closure and help maintain proper cooling. It stops cold air loss and reduces frost build-up when sealing correctly. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps reduce frost and moisture buildup inside the compartment
• Can improve cooling consistency and reduce energy waste when effective
• Commonly replaced for visible cracks, tears, or a flattened seal that no longer closes snugly

• Disconnect power to the appliance before starting any service
• Clean the door frame and mating surface before installing the new gasket
• Align the gasket evenly around the door and press into the channel until fully seated
• Check door alignment and hinges to ensure a proper long-term seal