Need Help?
Call
Replacement washer lid that covers the tub opening. Restores a secure, smooth-closing top when the original is cracked, warped, or broken at the hinges.
Replaced the lid Read more
Fix a cracked or broken dispenser drawer that won't close properly or slide smoothly. This direct-fit drawer restores organized detergent storage in your washer.
Replaced tray, The only difficulty was connecting the drain hose to the bottom of the tray. Difficult to get hand on the hose. Read more
Fix no hot water, leaking when washer is off, or weak water pressure. This triple water inlet valve controls hot, cold, and warm water flow. DIY-friendly repair.
Replaced solenoid valve. Repair summary: Turn off H/C water supply, disconnect hoses. Unscrew 3 screws rear of main panel. Slide front panel laterally then pull up to remove. Unscrew 2 screws on solenoid valve part. Disconnect spade electrical connectors and remove defective part. Insert new part and do everything I just said in reverse. It was so easy a drunken monkey could have done it. Read more
Washer won't advance cycles or skips rinse/spin? Timer controls wash, rinse, and spin cycles. Common DIY fix—most complete repair in 10 minutes.
I diagnosed the problem, identified faulty parts, and replaced those components. Read more
Fix no hot water, slow filling, or screaming noise during fill. This washer water inlet valve controls water flow into the tub. Moderate DIY repair.
Replaced water inlet valve Read more
The Motor Spring is an OEM replacement part for Whirlpool top-loading washing machines. This spring applies proper tension to the agitator assembly during wash cycles.
Causes of a bad motor spring can include damage from unintended impacts or fatigue after extended use. Over time, constant movement may cause the spring to weaken.
Symptoms of a bad motor spring include:
This OEM Whirlpool replacement is also compatible with some Kenmore, Admiral, Estate, and Roper top-load washer models as well.
Replaced with thrust bearing kit. Watched your video and it took about 10 minutes to fix. Thanks Read more
Washer not spinning or making loud grinding noises? The rotor assembly commonly fails when splines strip. Moderate DIY repair in 1-2 hours with basic tools.
Replaced rotor assembly due to hub being stripped. New part was upgraded with steel insert. After watching youtube video on AppliancePartsPros site, it took about 15 minutes for entire job. Part arrived in two days. Great service. Read more
The Float Assembly is an OEM part for LG washing machines. This part monitors and controls the water level within the appliance. It's a safety feature that prevents water overflow and potential flooding, contributing to the efficient operation of the washing machine by maintaining the correct water level for each cycle.
Causes of a bad Float Assembly can vary from simple blockages that prevent the float from moving freely to electrical faults within the switch mechanism.
Symptoms of a bad Float Assembly include:
This OEM LG part is also compatible with some Kenmore models.
The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more
Washer won't start or shows door lock error? This door lock switch keeps the door secured during wash cycles. DIY repair in 15-20 minutes with video.
First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more
Replacement control knob for washing machines. Installs on the control panel to select cycle and temperature settings. Needed when cracked or broken.
Replaced the timer Read more
Washer not draining or making groaning noises during drain cycle? This drain pump assembly removes water and debris. Check for clogs first; moderate DIY.
Washer won't fill with water or only fills with hot? The water inlet valve controls water flow into the tub. DIY repair takes about 30 minutes.
This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more
Connects washer tub to drain pump. Replace if cracked, split, or chewed by rodents. Common wear from chemicals and rubbing against machine components.
Ordered the part got it in 2 days Read more
Washer keeps filling when off or won't fill at all? The water inlet valve controls flow into the tub. DIY-friendly repair with video guide available.
I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more
The Clutch Motor is an OEM part for LG washing machines. This motor engages the clutch mechanism, allowing the washer to switch between agitating and spinning cycles effectively.
Causes of a bad clutch motor can include wear and tear over time, electrical issues, or mechanical failure due to overloading or improper use.
Symptoms of a bad clutch motor include:
This OEM LG part is also compatible with Sears/Kenmore models.
When I looked up LG washer E6 code on the web I saw the tip from LG: unplug the washer and call for service. To me that's a challenge. I saw the AppliancePartsPros.com story on Google, read it and decided to try the solution that worked for other people. A clutch shifter motor that was around $20. I checked a few local appliance parts stores and no one carried the part I needed in stock (even though their websites said available for pickup). I then ordered the part through AppliancePartsPros on... Read more
Fix a detergent lid that won't stay closed or open properly with this dispenser lid pin. Simple repair with video guide—most DIYers complete in minutes.
Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.