Washer Parts

This was the motor control board (also called the speed control board, motor control unit, or MCU in various places across the web). The repair was straightforward, except for two complications. First the old part was difficult to access in this model washer (Frigidaire Gallery Series front load washer). Instead of being easy to reach on the left side where there was space, it was sort of behind the actual motor on the right side of the housing. I spent some time trying to figure out... Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

• Noisy

I just wanted to put my experience here for all to see. I have a Maytag Neptune, MAH5500BWW, one of the original ones. I bought it back in 2002 and it has done many many loads of wash faithfully. So when the bearings started to get loud I thought it best to replace them, the seal kit and the belt. I did my research as best I could and decided to order the OEM parts from an appliance supplier. If you are replacing the bearings, watch on line videos prior to performing the job. It will... Read more

My Mom's Kenmore had a burnt plastic smell after a thunderstorm. Found motor capacitor had melted through, dumping liquid platic "spaghetti" onto the insulation blanket under the washer. All other compents looked fine. Told her not to use it until I replaced capacitor. The washer is 4 yrs old but the new capacitor revision was 3 letters higher, so they've made some design changes. Externally it looks the same. There is a large number on the capacitor, but the part is ordered by the much... Read more

• Will not drain

Checked the circuit board to see if R11 was burnt and it was. They told me if the wax motor had a brown tip that I would have to replace the Machine control circuit board as well as the Wax motor. I ordered the new parts put them in and it worked. Read more

• Will not agitate
• Will not drain
• Won't start
• Timer will not advance

Ordered new lid switch and plunger. Watched help videos and installed new parts, Washer works like new. Read more

Water valve not closing all the way. Water keep entering washer even with power cord unplugged. Parts I ordered fit perfect. Ordered on Thursday night , parts there Saturday. Great service and shipping. Thank Read more

I could not find specific online instructions for this job. Here are some tips. 1. Unplug the washer. 2. Unscrew the dial on the broken timer. 3. Gently pry up the thin plastic place-indicator plate (the thing with the arrow under the dial) with two flathead screwdrivers. 4. Unscrew the two hex screws holding the old timer in place. 5. Unscrew the phillips-head screws holding the console in place and flip up the console. 6. Remove the electrical connector from the bad timer, and remove the bad... Read more

I ordered the valve. Watched a video and installed it in 30 minutes. Works perfectly. Read more

I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

Replaced solenoid valve. Repair summary: Turn off H/C water supply, disconnect hoses. Unscrew 3 screws rear of main panel. Slide front panel laterally then pull up to remove. Unscrew 2 screws on solenoid valve part. Disconnect spade electrical connectors and remove defective part. Insert new part and do everything I just said in reverse. It was so easy a drunken monkey could have done it. Read more

Purchased a fabric softener dispenser from appliance parts pros removed cap from agitator and replace with the new fabric softener dispenser and problem solved. Read more

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more