Axle, Roller, Pulley Parts

Replacement shaft that secures and guides the dishwasher float for accurate water level detection. Needed when the original shaft is worn or broken.

Replacement bearing for canister vacuum wheel assembly. Installs inside roller axle to ensure smooth movement. Replace if worn, cracked, or missing.

Dishwasher rack rail support assembly that mounts inside the tub to guide the dish rack. Replace if cracked, broken, or worn, causing poor rack movement.

This bearing helps the appliance's rotating assembly turn smoothly and reduces metal-on-metal wear for quieter, more reliable operation. Replace a worn bearing to address noise and movement issues that affect performance. What it does:

• Supports the drum or tub shaft so it rotates with minimal friction
• Reduces grinding, rumbling, or squeaking noises from the rotating assembly
• Helps prevent excessive wobble or vibration during spin cycles
• Limits metal wear that can lead to leaks or further component damage

• Disconnect power and water before starting work
• Inspect surrounding seals, shafts, and mounting surfaces for wear while replacing the bearing
• Use correct tools and replacement hardware; follow OEM instructions for torque and alignment

V-pulley that guides the drive belt for smooth drum rotation. Replace if worn, cracked, or causing belt misalignment. Restores quiet operation.

Idler pulley assembly that maintains tension on the dryer drum belt. Replace if the pulley is worn, noisy, or causing the belt to slip or squeak.

This bearing assembly supports the dryer drum and helps the drum rotate smoothly for quiet, even drying. Replacing a worn bearing restores stable drum movement and reduces noise and vibration. What it does:

• Provides a low-friction support surface for the dryer drum, helping it spin properly
• Prevents drum wobble and off-center rotation that can wear belts and rollers
• Reduces squealing, grinding, or rumbling noises caused by a failing bearing
• Helps maintain even drying by keeping the drum aligned

• Disconnect power and fuel (gas) supply before starting any repair
• Access typically requires removing the dryer front or rear panel and drum; refer to a model-specific repair guide
• Use proper tools and support the drum during removal to avoid damage
• Inspect adjacent parts (shaft, seal, rollers) for wear and replace if visibly damaged

This base shaft is the support shaft that helps the washer's tub or drum stay aligned and rotate smoothly. Replacing a worn shaft restores proper drum support and reduces noise, wobble, and uneven operation. What it does:

• Provides a stable pivot and support for the tub/drum during operation
• Transfers rotational force from the drive components to the drum assembly
• Prevents excessive wobble, vibration, and metal-on-metal contact when intact
• Worn or damaged shafts can cause noise, drum misalignment, or premature bearing wear

• Disconnect power and water supply before servicing; follow all safety precautions
• Replacement typically requires removing the cabinet and drum assembly for access
• Inspect adjacent bearings, seals, and mounting hardware and replace if worn
• Use appropriate tools and follow the OEM service manual

Replace your washer's drive pulley if cracked, worn, or damaged. This rotating component transfers motor power to the drum belt for smooth operation.

Fix detergent door that won't open or latch properly. This dispenser plunger actuator restores mechanical engagement between the lid and release mechanism.

Replacement door hinge roller for ovens and ranges. Installs on the door hinge mechanism to allow smooth opening and closing. Order when worn or broken.

This genuine OEM replacement part is a pulley assembly for dryers. Sometimes called an idler arm, the pulley assembly keeps the dryer drive belt under tension as the belt wraps around the dryer drum. If the dryer is no longer spinning properly and is making a lot of noise, the pulley assembly may need to be replaced. Luckily this repair is a relatively simple process.To remove the old dryer pulley assembly, start by making sure the dryer is unplugged. Remove the lint screen from the top of the dryer. Remove the two Phillips screws by the lint screen opening. Depress the clips that hold the top cover down. Lift the top cover and keep it in an upright position. Disconnect the wire harness to the switch that separates the connector. Remove the screws on the front panel. Lift the panel forward and set it to the side. Next, lift the drum and locate the pulley assembly under the drum. Lift the belt off the motor pulley to remove the assembly. Set the new pulley assembly in the same position as the old one and make sure everything is aligned. Rotate the drum to make sure it rotates smoothly. reinstall the panels.This replacement part is sold individually and is compatible with Bosch, Gaggenau, and Thermador dryers.

Spiral pin secures the roller axle in your dishwasher's lower rack assembly. Replace if the pin is missing, bent, or dislodged to restore stability.