Burner & Related Parts

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.

This kit includes the orifice spuds and components needed to convert a natural gas range to liquid propane (LP) operation. The orifices regulate the gas flow to the surface burners for proper flame size and safe combustion. This kit is required when switching fuel types - without the correct orifices, burners may produce irregular flames, soot, or fail to ignite properly.

Burner head sits on the base and distributes gas through precision ports for even flame. Replace if cracked, clogged, or corroded for proper ignition.

The Burner Cap is an OEM part for Bosch gas cooktops. This small black burner cap safely contains the flame underneath to concentrate heat efficiently for precise cooktop control. Reliable burner caps are crucial for safety, performance, and aesthetics.

Causes of a bad burner cap can include warping or cracking from continuous exposure to high heat over the long run, as well as surface scratching or punctures.

Symptoms of a faulty cap include:

• Flames escaping beyond cap and licking up sides of cookware
• Visible damage or deterioration on cap surfaces
• Inability to adjust flame height as intended
• Burners no longer heating or shutting off properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This secondary gas valve solenoid coil energizes the dryer's gas valve so the burner can ignite and stay lit. Replacing a weak or failed coil restores consistent heat and helps resolve intermittent no-heat or flame drop-out issues. What it does:

• Works with the companion coil to open and hold the gas valve during burner operation
• A weak/open coil can cause tumbling with no heat
• Burner lights then goes out within seconds or heats intermittently
• Repeated clicking or glowing igniter without flame

• 1 secondary gas valve solenoid coil

• Disconnect power and shut off gas supply before servicing
• Access the burner/gas valve assembly; note wire positions and remove the old coil/retainer
• Seat the new coil on the valve stem, secure the retainer, and reconnect wiring firmly
• Restore gas and power; run a test cycle and check for leaks

• If one gas valve coil has failed, the companion coil is often near end-of-life; replacing both together can improve reliability

Replace your gas cooktop burner head if it's clogged, scorched, or worn. This part distributes gas through precision ports for even flame distribution.

This is the base component of a surface burner on a gas or electric range cooktop. It sits on the cooktop and distributes heat evenly for cooking. Replace this burner base if you notice uneven flame patterns, visible damage or warping, or if the burner cap no longer seats properly.

Burner head sits atop the gas valve and distributes flame evenly for cooking. Replace if cracked, rusted, or corroded to restore proper flame distribution.

Surface burner cap sits over the burner head to shape the flame. Replace if cracked, chipped, or worn to restore even heating and proper flame distribution.

Replacement double burner assembly for gas range cooktops. Installs under the main top to route gas to two burner outlets. Replace if damaged or worn.

Approx 3 inches in diameter

Burner head component that sits atop the gas burner base on cooktops and ranges. Replace if warped, cracked, or no longer fitting correctly.

Gas valve control assembly for ranges. Manages gas flow to burners and allows precise flame adjustment. Replace if worn, leaking, or damaged to restore control.

LP conversion kit converts natural gas cooktop burners to propane fuel. Includes orifices and hardware to safely adapt fuel delivery system when switching fuel types.

This replacement coil controls the gas valve's opening and holding action during burner operation. Replacing a weak or failed coil restores reliable ignition and steady heat for consistent drying performance. What it does:

• Powers the valve to open during ignition (booster) and keeps it open while heating (holding)
• Helps resolve: igniter glows but no flame, burner lights then shuts off, no heat, intermittent heat/long dry times
• Restores proper gas flow for consistent temperatures
• Direct-fit electrical connection for the valve solenoid

• 1 booster & holding coil

• Disconnect power and shut off gas supply before servicing
• Allow the burner assembly to cool; access the gas valve compartment
• Label and disconnect wires; replace the coil in the same orientation; secure clips/brackets
• Restore gas, check for leaks with an approved solution, then test burner operation

Burner base for gas ranges that directs gas to the burner head and holds the orifice. Replace if cracked, rusted, or broken to restore proper fit.