Cable Or Retainer

Secures the dispenser lever in place on your refrigerator. Replace if retainer is cracked, broken, or missing to restore proper lever stability.

This drive belt links the dishwasher's motor to the pump so the machine can circulate wash water and drain properly. Replacing a worn or broken belt restores wash action and helps eliminate slipping or squealing during cycles.

• Transfers motor power to the pump for water circulation and draining
• Common fix for no wash action or poor cleaning
• Can address squealing/chirping noises or a burning rubber smell
• Replaces belts that are cracked, frayed, stretched, or glazed

• Disconnect power and turn off the water supply before servicing
• Remove the lower access/toe panel to reach the motor and pump area
• Note belt routing; rotate the old belt off the pulleys and install the new belt the same way
• Check pulley alignment and hand-rotate to seat the belt before running a test cycle

Door pulley rope for dishwasher door latch mechanism. Replace if frayed, broken, or snapped from repeated use. Includes rope and plastic retainer.

This arm valve installs in the dishwasher's spray arm feed to control water flow. It helps maintain proper pressure so the spray arm spins and distributes water evenly for effective cleaning.

• Directs water through the spray arm and helps maintain wash pressure
• Prevents unintended backflow that can reduce spray performance
• If worn, stuck, or missing, lead to weak spray or poor cleaning results
• Common signs include intermittent wash coverage or spray arm not rotating as expected

• Disconnect power and turn off water before servicing
• Remove the rack/spray arm or feed manifold to access the valve
• Note the valve's orientation and seat the new valve fully in the same direction
• Reassemble and run a quick cycle to check for proper spray and leaks

Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.

Rope spring assembly that connects the dishwasher door to the base for smooth opening and closing. Replace if broken, frayed, or missing tension.

Guides the door balance cable in your dishwasher's hinge system. Replace if cracked, broken, or causing squeaking when opening the door.

Guides the dishwasher door balance cable for smooth operation. Replace if cracked, worn, or causing squeaking when opening or closing the door.

Secures the door cable assembly in your dishwasher. Replace this retainer if cracked, broken, or missing to restore proper door tension and operation.

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Rope cable that connects the door hinge spring to the dishwasher frame. Replace if broken, frayed, or snapped to restore door counterbalance support.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Secures the clear lens on your range's control panel. Replace if cracked, broken, or missing to keep the lens properly seated and prevent shifting or rattling.

Secures the drive motor to its mounting bracket. Replace if cracked, broken, or missing to keep the motor and blower aligned and stable during operation.

Small mounting clip that secures internal components in your laundry center. Replace if broken, missing, or worn to restore proper panel alignment.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.