Cap Or Cover

Protective cover for your dryer's terminal block electrical connections. Replace if cracked, broken, or missing to safely cover wire terminals.

Rear cabinet cover panel for washers. Encloses the back of the washer cabinet. Replace if cracked, damaged, or missing to restore appearance.

A single replacement cap handle screw that secures the decorative handle cap to the appliance door, restoring a snug fit and preventing the cap from shifting or falling off. Fits the factory handle cap design. What it does:

• Secures the handle cap to the door handle assembly so the cap stays aligned and tight.
• Fixes common symptoms like a loose or rattling handle cap or a cap that shifts when the door is opened.
• Replaces missing or worn screw hardware to restore original fit and appearance.
• Small OEM-style screw sized for the handle cap mounting location.

• One cap handle screw (black), matching the original hardware.

• Use the correct screwdriver or bit to avoid stripping the screw head.
• Hand-start the screw to ensure proper threading; do not overtighten.
• No special tools or electrical disconnection typically required, but follow appliance-specific service guidance.

Black chevron-style top trim cap for refrigerator upper control area. Replace cracked, chipped, or faded trim to restore front appearance and finish.

This white cover hinge replaces a worn or broken hinge that supports and pivots the appliance cover, restoring proper alignment and smooth opening/closing for the lid. Designed as a direct-fit replacement where specified. What it does:

• Provides a secure pivot point so the cover or lid opens and closes smoothly
• Keeps the cover aligned to prevent sagging, rubbing, or binding
• Restores a proper seal/closure when hinge wear causes gaps or misalignment
• Helps eliminate rattling or excess play caused by a damaged hinge

• Disconnect power (and water if applicable) before starting any repair.
• Handle the lid/cover carefully during removal to avoid dropping or injury.
• Basic hand tools are typically required; follow your model's service diagram for location and fastener details.
• Replace with the same OEM part number to ensure fit.

White plastic corner cap that snaps onto refrigerator door corners to conceal fasteners and protect hinge areas. Replace if cracked, broken, or missing.

Protective cover cap for refrigerator temperature sensor. Snaps into place to shield sensor from damage. Replace if cracked, broken, or missing.

White plastic cover cap that conceals mullion screws in your refrigerator. Replaces cracked, broken, or missing screw covers for a finished appearance.

White plastic end cap for refrigerator front grille assembly. Replaces missing, cracked, or broken grille caps. Snaps onto grille edge for clean finish.

Black plastic grille end cap for refrigerator base grilles. Replaces broken, cracked, or missing caps that secure grille panels at the edges.

Protective cover for the fresh food compartment temperature sensor in your refrigerator. Replace if cracked, broken, or missing to shield the thermistor.

Sliding cap for refrigerator shelf frames. Replaces broken, cracked, or missing caps on glass shelf assemblies. Installs on shelf frame edges.

Plastic cap that covers and protects the handle mounting screw on your refrigerator door. Replace if cracked, broken, missing, or discolored.

Replace your refrigerator's hinge cover if cracked, broken, or missing. This plastic cap installs over the door hinge mechanism for a finished look.

Covers and protects the top door hinge assembly on your refrigerator. Replace this plastic cover if it's cracked, broken, or missing to restore a clean finish.

This cover hinge top is the upper cabinet hinge piece that supports and guides a refrigerator/freezer door or access cover, restoring proper alignment and smooth opening for reliable daily use. It's a direct-fit replacement designed to match OEM form and function. What it does

• Secures the upper edge of the door or top cover and provides a pivot point for opening and closing.
• Restores proper door alignment to prevent sagging or uneven gaps.
• Helps eliminate binding, sticking, or rough door movement.
• Reduces noise caused by a worn or damaged hinge.

• One cover hinge top.

• Disconnect power to the appliance before starting any repair.
• Support the door or cover during removal to avoid dropping or damage.
• Use basic hand tools; follow the appliance service manual for torque and alignment steps.
• Handle trim or glass pieces carefully to avoid chipping or breakage.