Clip Or Clamp

To use with BOOT #wh8x246

Grounding clip for top-load washers ensures proper electrical grounding. Replace if damaged, corroded, or missing to maintain safe operation. Verify fit with your washer model number before ordering.

Secures wiring, tubing, and trim inside your dishwasher or refrigerator to prevent rubbing and movement. Replace if broken or loose to maintain proper positioning.

Secures the lower front grille or trim panel to prevent rattles and gaps. Replace when clips break or go missing for a snug, aligned fit. Verify compatibility.

Secures the door boot gasket in its groove to maintain a watertight seal. Replace if stretched, bent, or broken to stop front-panel leaks. Verify fit.

Secures the stirrer fan and cover assembly in your microwave. Replace if melted, damaged, or missing to prevent cover wobbling and ensure proper operation.

Secures wiring and hoses in your laundry center to prevent rubbing and wear. Replace when broken or missing to maintain proper routing. Verify fit.

Retaining clamp secures hoses and tubes to prevent leaks and loose connections in your washer dryer combo. Replace if worn or damaged. Verify fit with model.

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

Secures front panel on laundry centers. Replace if broken or panel becomes loose. Verify fit with your model number before ordering this clip.

This clamp secures a flexible appliance hose to a fitting to help prevent leaks and keep connections tight. It's a small but essential part that restores a proper seal on water or drain lines. What it does:

• Holds a hose firmly to a tailpiece, barb or connector to reduce leaks and hose slippage
• Helps stop intermittent dripping or pooling caused by loose hose connections
• Restores a proper seal after hose replacement or maintenance
• Works on common appliance water/drain lines where this clamp style is used

• One hose clamp

• Disconnect power and shut off water to the appliance before starting any work
• Allow the appliance and hoses to cool if recently used; use gloves and eye protection
• Use appropriate pliers or a screwdriver (depending on clamp style) to remove and install the clamp; avoid over-tightening
• Inspect the hose and fitting for damage; replace the hose if cracked or worn

This water filter latch secures the refrigerator's filter housing so the cartridge stays in place and seals correctly. It restores proper filter engagement to help prevent leaks and ensure consistent water dispensing. What it does:

• Secures the water filter cartridge in the housing so the filter locks into place
• Helps maintain a proper seal to reduce the risk of water leaks
• Prevents the filter from becoming loose or falling out during normal use
• Can resolve symptoms like a loose filter, leaking at the filter area, or poor dispenser performance

• Turn off the water supply and remove the filter cartridge before servicing
• Handle plastic parts gently to avoid cracking; confirm the latch seats fully in the housing
• Do not use the appliance if water leaks persist after replacement

The washer Hose Retainer Holder Clip is an OEM part that mounts behind the control panel on LG front-loading washers. It positions water supply hoses to prevent kinks or stress that leads to leaks over time. 

Causes of a failed clip include fatigue from years of front-load vibration and damage from any installation or repair work behind the control panel.

Symptoms of an insufficient hose retainer clip include:

• Loose, misrouted, or flopping hoses behind the control panel
• Bulging or kinked hoses that restrict water flow
• Water leaks at hose connections

This OEM replacement clip is compatible with select Kenmore front-loaders.

Secures water hoses to fittings and prevents leaks in your washer. Replace when connections loosen or clamps lose tension. Verify fit with your model.