Need Help?
Call
Replacement lower dishrack for dishwasher bottom level. Restores dish organization when original rack is rusted, cracked, or falling apart. Includes tines.
Order both racks, upper and lower. The lower rack came fully “assembled”, all four sets of wheels came installed. The upper rack was a little more challenging. I had to YouTube how to remove the upper rack. The new upper rack was bare. Had to install several parts and two of them were the side support and height adjustment pieces. There no instructions and I couldn’t find anything specific on YouTube on how to remove/install these. I learned with the second one that you need to slide the height... Read more
If your dishwasher won't fill with water or makes thumping noises, the water inlet valve likely needs replacement. Moderate DIY repair from base.
This was not my first rodeo have repaired our appliances and those of our daughters for years, have ordered parts from this site several times. We had a cold spell in Texas, as you may have heard. We weathered it okay but left the dishwasher closed on one of the colder nights, woke up to water on the floor in the kitchen. Turned off the supply line, shut off the dishwasher power, bailed out the bottom, and mopped up. Had a fair idea of what the cause was, checked a few websites, watched some... Read more
This plastic cap covers the end of the dishwasher rack slide rail to protect the tub interior and ensure smooth rack movement. Replace if the rack is difficult to slide, makes scraping noises, or if the cap is missing or damaged.
Two years ago replaced all four roller assemblies of affected side. Problem recently reoccured on the opposite side. Replaced all four roller assemblies on that side. Entire repair took about twenty minutes. Read more
Dishwasher not draining or leaving water in the bottom? This pump and motor assembly circulates and drains water. 2-hour DIY repair with video guide.
I fixed it by installing a ge pump and motor assembly. it works fine Read more
Ring bearing supports spray arm rotation in dishwashers. Mounts at spray arm base to allow free spinning. Replace if cracked, worn, or missing.
Replaced upper and lower spray arms, plus nylon bearings. Read more
Creates a watertight seal around your dishwasher door to prevent leaks during wash cycles. Replace when worn, cracked, or causing water leakage. Verify fit with your model number.
After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more
Replace your dishwasher's broken, cracked, or clogged spray arm. This rotating water distribution arm installs on the rack and ensures proper spray coverage.
Ordered a replacement part off another site that came in with an incorrect molded connection to the Spray Arm. The part broke my tabs on the Spray Arm and instead I bought both parts from this site. Both items were correct and resolved the issue. Read more
Dishwasher not filling with water or leaking when off? The water inlet valve controls flow during wash cycles. DIY repair typically under 30 minutes.
First I cleared the food chopper area. There were things there, bits of plastic for instance, but it wasn't the reason for the dishes not getting sprayed off. The dishwasher continued to only partially fill and not circulate the water. I started the dishwasher, let the pump start and then opened the door and filled up the dishwasher manually. It sprayed water as it should, cleaning the top rack quite well. I figured the issue was not the float switch, since some water was coming in. So I... Read more
This base is the lower cabinet support that helps keep the appliance stable and holds internal components in their correct position. Replacing a damaged base restores proper fit, alignment and reduces cabinet movement. What it does:
Tried cleaning them with bristled brush but just wasn't cutting it. Replaced with new. Hoping for cleaner dishes. Read more
Fix a dishwasher that won't start or won't stay closed with this door latch kit. Straightforward repair in under 30 minutes with basic tools.
I turned off the power then removed the six or so screws from the back of the top panel. I marked the two front wires on the latch with tape so I would not get them confused. I removed the two screws holding the latch on--these take a six pointed star bit on the screw driver--the bit is in most screw driver sets with interchangeable heads. I then connected the wires to the new latach and put everything back together. The whole process took between ten and fifteen minutes. Read more
The Diverter Motor Assembly is an OEM part for LG dishwashers. It is a critical component used to control the direction of water flow within the dishwasher, ensuring that water is properly diverted between the different spray arms during various wash cycles.
Symptoms of a failing Diverter Motor Assembly include:
Causes of a bad diverter motor can include wear and tear from regular use, electrical issues such as faulty wiring or motor failure, and mechanical obstructions or debris that prevent the diverter from moving smoothly.
This OEM LG part is also compatible with Sears/Kenmore models.
I ordered a new vario motor and a soap dispenser. I turned off the water and the breaker, disconnected the water line and the power at the front base of the unit, disconnected the drain hose from the garbage dispenser, and pulled out the dishwasher and laid it on a blanket on its face. I unscrewed and removed the plainly visible vario motor on the bottom of the machine and removed the cam from the shaft. I then used a needle nose plier to carefully turn the D-shaft on the new motor to exactly... Read more
Washer not filling with water or showing 4E error? The water inlet valve controls flow into your machine. DIY repair in 15-40 minutes with video guide.
I found a youtube video about replacing the hot water valve in a Samsung washer. It looked pretty easy. I had been very satisfied with an earlier order from AppliancePartsPros.com, so I ordered this part on Sunday after 9PM, standard delivery, hoping to get the part by the end of the week. I was flabbergasted to receive the part TUESDAY MORNING! Wow! I followed the instructions in the youtube video exactly. It took around 15 minutes, because I was being very careful not to drop screws in... Read more
Fix a dishwasher that won't start, beeps but doesn't run, or has no display lights with this electronic control board. Moderate DIY repair.
The circuit board under the machine needed replacing. Pretty easy if you are willing to not force it in. Two screws, four all different plugs, two guide holes for the wiring. I bought a latch but did not need to install it. Read more
Dishwasher won't start or displays flashing lights? The control board manages cycles, detergent dispenser, and water release. DIY repair in 10 minutes.
I went to appliancepartspro.com and found out that the problem could be the main circuit board. I went on and ordered the part, knowing it could be returned if necessary, but it was like music to my ears when I installed the part, myself, and turned the power back on. Easy. Thanks appliancepartspro. Read more
The Dishwasher Interface Cover is an OEM part for GE dishwashers. It covers and protects the control panel and touchpad of the dishwasher, ensuring that the electronic components are shielded from moisture and physical damage.
Over time, the interface cover can become damaged or worn out due to regular use, exposure to water and cleaning agents, or accidental impacts. A compromised cover can affect the usability of the control panel and potentially lead to malfunctions.
Symptoms of a bad Dishwasher Interface Cover include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Had to remove the door from the main body of the dishwasher and then take the outer door apart from the inner door. Find a good video that showed how to do this but it was not exactly like the model of GE dishwasher that I have. Once you know how to remove the panel it went fairly quick. But in removing the inner door I broke the one end of Attach Strip Rh so I order a new one plus in taking the Graphics Asm apart to get to the UI board the small tab that holds everything together broke off. So... Read more
Dishwasher not draining or leaving standing water? This drain pump removes water during drain cycles. DIY-friendly repair with basic tools in under an hour.
First determined drain discharge hose was clear. Turned of power to dishwasher. I did not find it necessary to remove the dishwasher. I simply removed the lower service panel at the floor and was able to easily remove the defective pump, unplug it, replace the small rubber check valve flapper before the pump inlet and reinstall the new pump assembly. The dishwasher surprisingly cleans and runs quietly like new again although I found no excuse for the pump failure as it is well designed. Never... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.