Need Help?
Call
Fix dishwasher not filling with water or slow fill issues. This inlet valve controls water flow into your dishwasher. DIY repair typically takes 15-30 minutes.
Replaced the water solenoid. Read more
Replaces cracked, broken, or melted lower spray arm in your dishwasher. Snaps into place on the lower rack. Common damage from falling onto heating coil.
Installed new sprayer arm. It was super easy. Read more
Replaces broken or worn dishwasher door springs and cables. Installs on both sides to restore door balance and prevent dropping. Kit includes springs and cables.
Got new replacement spring and cord for our Bosch compact dishwasher. A plastic retaining bracket that held the old spring also was broke but the new spring had its own piece that fit into a slot in the plastic frame, so i just popped it in there, connected the cord, and bingo. The door now works. I tried using the old spring, but it would not work because of the broke bracket. Read more
Fix H2O error codes and water fill issues with this dishwasher pressure sensor. Monitors water level for proper fill cycles. DIY repair in about 1 hour.
Tried to fix with a non GE part, didn’t work. Your GE brand pressure sensor worked like a charm Read more
Secures the dishwasher rack to prevent it from rolling out too far. Replace this clip if it's cracked, broken, or missing to keep your rack stable.
Replaced wheel assembly because prongs were broken and replaced track because wheel assemblies were rolling out from the track when extended. Read more
Replaces broken or worn lower rack carriers and rollers. Installs on both sides of the dishwasher lower rack to restore smooth gliding along tracks.
I was able to find the parts on your website. I was a little worried because there were no photos, but the parts were correct, and it was an easy fix! Read more
Fix dishwasher leaks on the floor with this door gasket and strike kit. Easy 15-minute repair—gasket presses into groove, no glue needed. Video included.
I followed your step by step instructional online video. That is one great tool you are providing for your customers! Read more
Replacement spray arm for dishwashers. Snaps into the rack to distribute water through multiple jets. Replace if broken, cracked, or missing clips.
Replaced both the Spray Arm and the Spray Arm Water Supply Tube. Highly recommend replacing base plate whenever the Spray Arm Water Supply Tube is replaced. Plastic tabs on the base plate hold those parts together and are likely to break (as seen on Appliance Parts Pros installation video!!!). I sensed tab weakness so just transferred parts needed from the new tube to the old tube and reinstalled the original tube / base plate assembly rather than risk breaking those plastic tabs. I should... Read more
Dishwasher not dispensing soap or dispenser door won't open? This detergent dispenser fixes dispensing failures. Moderate DIY repair, about 30-45 minutes.
The part went on easily. U Tube video answered any questions I had before installing. Read more
Replacement dishwasher rack assembly that holds dishes during wash cycles. Needed when original rack is rusted, cracked, or wire coating is worn.
To say using Appliance Parts Pros made things as simple as it gets, is an understatement. I was able to order the parts simply by using their website and having my dishwasher make and model number. Images of the parts make confirming the order even better. They have an on line question/answer cue if needed and even offer a call in for advice number. Once the order arrived, I verified the parts and began installation. Take a few pictures of the appliance from different angles before you start.... Read more
This is the upper dishrack assembly for a dishwasher, providing the sliding rack where cups, glasses, and smaller items are loaded for washing. It includes the rack frame and tine rows that hold dishes in place during the wash cycle. Replace this assembly if the rack is rusted, has broken or bent tines, or if the rollers no longer glide smoothly on the tracks.
Fix a dishwasher that won't start, has flashing lights, or is completely unresponsive. This control board manages all cycle phases. Moderate DIY repair.
My GE dishwasher (GDT605PMM0ES) had started going in and out of service but if I unplugged it and plugged it back in it would work a few more times. Then one day that old trick didn't work anymore. Looked at what might be the issue on the internet and most signs pointed to the configured service machine control board or the configured Ui board. I ordered both, not really which was bad, but started with the Ui board first because the service machine control board showed it was receiving... Read more
Fix a mixer that won't run, starts at full speed then stops, or won't shift speeds properly. Replace the speed control board in about 30 minutes.
The fix was very easy. Control assembly is easy to access by removing 5 phillips screws. Unplug the wiring from the old assembly being careful to note which wire goes to which connector. Install the new assembly and connect the wiring. Read more
Dishwasher not cleaning or spray arms not moving? The circulation pump distributes water through the tub. Requires full dishwasher removal. Video available.
The water just sat in bottom of the tub, but the dishes never got wet. The water would drain out at the end of the cycle. I took a chance that it was the circulation pump and not the control panel since everything else seemed to be working. I replaced the circulation pump &motor and the problem was solved. The hardest part was getting the DW out of the cabinet since it was a very tight fit due to the floor tile. The job of replacing the part only took about 15~20 minutes thanks to the repair... Read more
This is the flexible rubber or vinyl gasket that lines the opening of your dishwasher tub, creating a watertight seal when the door is closed during a wash cycle. It prevents water from leaking out around the door during operation. Replace it when you notice water pooling on the floor in front of your dishwasher, or when the gasket is visibly torn, stiff, or pulled away from the tub.
Upon taking the door apart it looked like the leak was coming from the vent so I replaced the vent cap, vent seal and the transition piece. I did not have to change the seals. It took me a while to figure out how to get the door apart, but once I did, it was fairly straightforward. Read more
The Tine Row Pivot is an OEM replacement part for Whirlpool dishwashers. This component is an integral part of the upper rack assembly, allowing the tine rows to fold down or pivot inward to accommodate taller items or create additional space within the rack.
Symptoms of a faulty tine row pivot may include:
Causes of needing to replace the tine row pivot can include normal wear and tear over time, physical damage from mishandling or impact, or issues with the pivot mechanism becoming corroded or obstructed.
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.
Ordered a new one. It took about 10 seconds to install. Now it’s like brand new. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.