Dispenser Parts

This cap is a small protective cover used on select appliances to close off an opening or fastener. Replacing a damaged or missing cap helps keep out debris and moisture while restoring a clean, finished appearance.

• Covers an exposed opening or fastener to protect internal components
• Helps keep out dust, moisture, and spills
• Restores a clean, finished look and prevents snags
• Replace if the original cap is cracked, missing, discolored, or won't stay seated

• Disconnect power and, if applicable, shut off water or gas before service
• Remove the old cap by pulling straight off or unthreading, as designed
• Align the new cap and press or thread into place without forcing
• Verify a secure fit before restoring power and connections

Broken or missing dispenser handle? This assembly restores a solid grip so your washer's dispenser opens smoothly. Easy DIY repair for most models.

White overflow grille for refrigerator water/ice dispenser. Replaces cracked, pitted, discolored, or missing grilles. Snaps into place below dispenser.

Fix washer leaks from the top or bleach not dispensing. This replacement bleach dispenser cup stops drips and restores proper bleaching. 10-min install.

Fix detergent leaking or improper dispensing with a new washer dispenser drawer. Replaces cracked or worn 3-compartment drawers. Easy DIY repair.

This is a replacement refrigerator storage drawer. It restores smooth sliding and dependable storage when the original drawer is cracked, warped, or missing, helping you keep items organized and easy to access. What it does

• Provides enclosed storage for food items inside the refrigerator
• Slides on the existing rails for easy access and organization
• Helps keep contents visible and separated from other items
• Common failure symptoms: cracks, broken tabs, drawer falling off tracks, hard to open/close

• 1 drawer

• Disconnect power and remove items from the drawer area before starting
• Fully extend and lift to remove the old drawer; clean the tracks
• Align the new drawer with both rails and slide it in evenly
• Do not force; ensure tabs and tracks are properly seated

Fix a broken or cracked washer dispenser drawer handle. Simple pull-out replacement—no tools needed. Compatible with many front-load washers.

Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.

White plastic grille that sits beneath the ice and water dispenser to catch drips and spills. Replace if cracked, stained, or missing for a clean look.

Fix a dispenser door that won't stay closed or rinse aid light staying on. Complete assembly includes latch, spring, and gasket. DIY-friendly repair.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

Dispenser won't open during wash cycle? This detergent dispenser restores reliable soap release and rinse-aid dosing. Moderate DIY repair with video.

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.

Fix detergent not dispensing or leaking from your washer's drawer. This dispenser drawer assembly replaces cracked or warped drawers. Simple installation.