Frigidaire Control Board

Note: This part is often misdiagnosed and requires electrical testing using a volt/ohm meter.

Important: When replacing this main board, if it does not power on or make a connection, you will also have to replace the display board. The display boards for some models are no longer available. Please refer to your specific model for the correct display board and availability.
 

The User Interface is an OEM replacement part for Frigidaire refrigerators. It is the digital control panel that allows for monitoring temperature settings and adjusting other functions.

Symptoms of a bad user interface include:

• Frozen or unresponsive touch buttons  
• Illegible or blank LED screen
• Inability to power on or adjust refrigerator settings
• Temperature display showing incorrect readings

Causes of a bad user interface can include failures in the electronic components from condensation or liquid spills over time. Physical damage to the wiring or circuit boards is another potential cause.

This part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Control Board Dryer is an OEM replacement part for Frigidaire electric dryers. As the central processing unit, the control board is responsible for operating all electronically controlled systems and components that enable the drying process. It precisely coordinates heating times and temperature, drum rotation, airflow, sensors, and more.

Causes of a bad control board can include damage due to moisture intrusion, defective electronic components, or general wear and tear over extended use.  

Symptoms of a bad control board include:

• The dryer failing to start, heat or tumble clothes
• Random restarting or stopping during cycles  
• Burning smells coming from the control board area
• Error codes flashing on the display

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore electric dryer models.

This surface element control board manages a dual radiant cooktop burner. It regulates power to the inner and outer coils so the element heats correctly, changes size as selected, and responds accurately to temperature settings.

• Controls power to a dual radiant surface element
• Directs inner/outer ring operation based on size selection
• Modulates heat output to match the set level
• Common failure symptoms: dual burner won't heat, only one ring heats, stuck on high, or erratic cycling

• Disconnect power at the breaker before servicing to avoid electrical shock
• Access is typically under the cooktop or rear top panel; refer to your model's service information
• Move wire connectors one at a time to the new board to maintain correct placement
• Handle the board by the edges and observe ESD precautions

The PC Board is an OEM replacement part for Frigidaire refrigerators. As the central "brain" of the refrigerator, it controls all electronic functions and directs operational tasks. The board receives input from sensors and buttons to orchestrate temperature regulation, defrost cycles, lighting, and more.

Causes of a bad PC board can include failure over time due to heat exposure, power surges damaging sensitive electronic chips, or liquid ingress corroding circuitry.

Symptoms of a bad PC board include:

• The refrigerator failing to cool or fluctuating temperatures
• Lights not turning on or functionality issues with buttons/displays
• Abnormal mechanical noises or failure to engage components

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Main Power Board is an OEM part for Frigidaire refrigerators. This board controls and manages the primary functions of the refrigerator, including temperature regulation, defrost cycles, and the operation of other electronic components. It serves as the central hub that ensures the appliance runs efficiently and effectively.

Causes of a bad power board can include electrical surges, overheating, or component wear over time. Exposure to moisture or accidental impact can also damage the board, leading to operational issues.

Symptoms of a bad Main Power Board include:

• The refrigerator not cooling or freezing properly
• Intermittent or complete loss of power
• Error codes displayed on the control panel
• The refrigerator running continuously without cycling off

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Main Power Control Board is an OEM replacement part for Frigidaire refrigerators. It is the central processing unit that controls all electrical functions and components within the refrigerator. The board receives input signals, processes them, and sends output signals to regulate temperature, monitor sensors, power accessories, and run diagnostics.

Symptoms of a bad main power control board include:

• Fluctuating or inconsistent temperatures  
• Components not functioning properly
• Error codes appearing
• Intermittent or complete power failures

Causes of failure can include moisture damage, power surges, component degradation over time, or physical damage.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This part is a replacement control kit. It is made to replace a broken or ineffective part in some models of ovens and ranges.In order to monitor the temperature and control the oven settings, the control kit needs to be in proper working order. In cases where this part is warped, corroded, worn, broken, or in any way ineffective, the control kit will need to be immediately replaced. Prior to undergoing repairs, it's critical that the oven is entirely disconnected from the power source. Always wear work gloves when attempting an appliance repair.This is a genuine OEM part that has been manufactured by Frigidaire and has been sourced directly from the manufacturer to ensure high quality. This control kit can be used with various different models of ovens and ranges that have been manufactured by brands that include Frigidaire, Electrolux, Gibson, Westinghouse, and others. This is a genuine OEM part and thus is made of high-quality, durable materials and is sold individually.

The User Control and Display Board is an OEM part for Frigidaire refrigerators. This part provides the interface for setting temperatures and controlling various functions of the refrigerator, displaying information like temperature settings, and error codes.

Common causes of a bad control and display board include electrical surges, wear and tear of electronic components, or damage from moisture or heat exposure.

Symptoms of a bad User Control and Display Board include:

• The display not lighting up or showing incorrect information
• Buttons not responding to inputs
• Inability to change temperature settings
• Error codes or malfunctioning indicators on the display

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electronic control board is the appliance's central controller, interpreting your selections and directing power to run each cycle. Replacing a failed board can restore operation when the console is dead, unresponsive, or cycles won't start or advance.

• Coordinates cycle timing and executes user-selected programs
• Switches power to components via on-board relays/triacs
• Monitors inputs/sensors and reacts to faults
• Common failure symptoms: no power/display, won't start, unresponsive buttons/knob, erratic lights or beeping, cycle won't advance

• Disconnect power before servicing; verify no voltage is present
• Use ESD precautions; handle the board by edges only
• Transfer any mounting brackets, screws, or decorative overlays from the original as required
• Reseat all connectors firmly; after install, run a test/diagnostic or a normal cycle to confirm operation

The Dishwasher Control Board is an OEM part for Frigidaire dishwashers. It is the central component responsible for operating and controlling all functions of the dishwasher. 

Causes of a bad control board can include moisture damage, short circuits, or normal aging of electronic parts over time. 

Symptoms of a bad control board include:

• The dishwasher not starting or functioning properly
• Lights flashing in unintended patterns  
• Inability to select desired wash cycles
• Issues with dispensing detergent or rinse aid

This OEM Frigidaire replacement control board provides genuine functionality and performance. It is also compatible with some Electrolux, Gibson, and Kenmore dishwashers.

This refrigerator control board is the central electronic module that manages key appliance functions for consistent temperatures and dependable operation. A failed board can cause no-cool conditions, unstable temperatures, or unresponsive controls; replacing it restores proper function. What it does:

• Interprets inputs from temperature sensors and user settings to run the appliance correctly
• Distributes power to components through relays and connectors
• Coordinates cooling and, on applicable models, defrost and fan operations
• Common failure signs can include no or intermittent cooling, warm temperatures, frost buildup, clicking from the control area, or unresponsive controls

• 1 control board

• Disconnect power to the refrigerator before servicing
• Use ESD precautions; handle the board by the edges only
• Photograph wiring; move connectors one at a time, ensuring keyed orientation and full seating
• After reassembly, restore power and allow up to 24 hours for temperatures to stabilize

The Defrost Control Board is an OEM part for Frigidaire refrigerators. This board manages the defrost cycle by controlling the activation of the defrost heater and the monitoring of the freezer's temperature. 

Over time, the defrost control board can fail due to electrical issues, wear from continuous use, or damage from power surges. 

Symptoms of a bad defrost control board include:

• Excessive frost buildup in the freezer compartment
• The refrigerator not cooling properly
• The defrost heater not activating
• Frequent cycling on and off of the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Control Board is an OEM component specifically designed for Frigidaire ranges. It is responsible for regulating and monitoring various electrical components of the range such as the temperature display, bake/broil elements, convection fan, and cooktop burners.

Symptoms of a bad control board include: 

• Inaccurate or inconsistent temperature readings
• Unresponsive controls and setting buttons 
• Intermittent or failed cooktop/oven functions
• Error codes appearing on the display

Causes of a bad control board can include exposure to heat over time, damage from liquid spills, or failure of electronic components on the board.

Replacing the control board ensures full functionality is restored. This OEM Frigidaire replacement will integrate seamlessly with all existing wiring and connections on your appliance.

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Don't risk further damage - replace yours before issues escalate.
 

The Control Board is an OEM part for Frigidaire ranges. This part controls the oven functions, including temperature regulation, cooking modes, and timer settings.

Causes of a bad control board can include electrical surges, moisture damage, excessive heat, or general wear and tear.

Symptoms of a bad range control board include:

• The oven or burners not turning on
• Unresponsive or malfunctioning control panel
• Incorrect temperature settings
• Error codes displayed on the control panel
• Oven not maintaining set temperature

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This OEM replacement part is a relay control board for ovens. The relay control board receives signals from the main oven control board. This part regulates the oven's temperature. If the oven is no longer heating properly or maintaining temperature it might be time to replace the relay control board. Luckily replacing this board is an easy repair. To replace the relay control board, begin by turning off all power to the oven. Once the power has been shut, move the oven away from the wall to gain access to the upper back panel. Remove the panel and locate the relay control board. Snap it out of its mounting brackets and remove the wire harness connected to it. Reinsert the wire connectors to the new relay board in the correct order. Secure the new board into its mounting brackets. Reinstall the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.