Lg Parts

The Tine Row Holder is an OEM part for LG dishwashers. It is a molded plastic bracket located inside the dishwasher that firmly holds the horizontal tine rows of the upper spray arm assembly in place. Subject to vibrations during the wash cycle, the tine row holder must securely grip this assembly.

Symptoms of a bad tine row holder include:

• Loosened or detached upper spray arm that causes insufficient washing 
• Rattling noises from loose components inside the tub 
• Potential leaks if the plastic material cracks fully over time

Causes of failure can include cracking of the holder plastic from solvent exposure and mineral buildup over thousands of wash cycles. Replace with this OEM LG part to ensure balanced water distribution to all areas of dishes. It is also compatible with Sears/Kenmore dishwasher models.

This Supporter, Leg is the base bracket that holds the leveling foot at the cabinet. It stabilizes the unit and enables precise leveling to help prevent rocking, vibration, and door or drawer misalignment during everyday use.

• Supports and locates the leveling leg/foot at the base of the cabinet
• Provides a secure mounting point for height adjustment and stability
• Helps keep the cabinet square and reduces wobble and vibration
• Common symptoms of a failed support include rocking, difficulty leveling, or a visibly cracked/bent bracket

• Disconnect power and protect flooring before moving or tilting the appliance
• Access the base area (remove the toe grille/kick panel if equipped)
• Unload the leg, remove mounting fasteners, and transfer the leveling foot to the new support if needed
• Reassemble and verify the unit is level front-to-back and side-to-side

This wire harness routes power and signals between the washer's control and multiple components. Replace a damaged harness to restore dependable operation when wiring is cut, brittle, or connectors are heat-damaged or corroded.

• Distributes electrical power and communication between the control board and components such as the motor, pump, valves, door lock, and sensors
• Maintains safe, reliable connections when insulation and terminals are intact
• Typical failure signs: intermittent operation, no start, specific loads not working (pump/motor/valves), or error codes traced to wiring faults
• Visible damage like chafed wires, broken connector locks, or burned/corroded terminals indicates replacement

• Disconnect power and turn off water supply before servicing; wear cut-resistant gloves
• Photograph and label connectors; move one plug at a time from old to new to avoid miswiring
• Route along original clips, channels, and grommets; keep wiring clear of sharp edges and moving parts
• Ensure all connectors are fully seated; test operation before final reassembly

This accessory assembly is the factory-specified kit used to attach or secure designated parts on your appliance. Replacing missing or worn pieces restores a solid, factory fit and finish.

• Provides the original mounting/attachment components specified for your model
• Replaces lost or damaged hardware after installation, moving, or service
• Helps correct loose, misaligned, or rattling parts caused by missing fasteners
• Maintains proper alignment and appearance of exterior parts such as trim or handles

• Disconnect power; also shut off water and/or gas supplies before servicing
• Protect finished surfaces; start fasteners by hand to avoid cross-threading or damage
• Follow your model's service or installation guide for correct order and placement
• After assembly, verify everything is secure and test operation before returning to service

This lamp cover encloses and shields the light bulb while diffusing illumination inside the appliance. Replacing a cracked, discolored, or missing cover restores safe, even lighting and protects the bulb from accidental contact and debris.

• Covers and protects the light bulb; diffuses light for better visibility inside the compartment
• Helps prevent bulb damage from impact, moisture, and debris
• Common symptoms: cover is cracked, warped/melted, yellowed, loose, or missing; exposed bulb or harsh glare
• Sometimes called a light lens; may rattle or fall out when tabs or screws break

• Disconnect power to the appliance and allow the lamp area to cool completely
• Handle the lens carefully; align tabs/clips and seat fully before securing—do not overtighten
• Inspect and replace the bulb if damaged or heat-darkened

This replacement drain tray sits beneath the refrigerator's ice/water dispenser to catch drips and splashes, helping keep the door area clean and dry. It restores a neat, finished look when the original tray is cracked, stained, or missing. What it does:

• Collects drips and minor spills from the dispenser to reduce mess on the door and floor
• Helps prevent water streaks and mineral-stain buildup around the dispenser recess
• Restores a secure, flush fit when the original tray is warped, loose, or broken
• Common signs: standing water in the recess, leaks running down the door, visible cracks, tray won't stay seated

• 1 dispenser drain tray

• Lock dispenser controls or power off the refrigerator to avoid accidental dispensing
• Pull the old tray straight out; clean any residue in the dispenser recess
• Align and press the new tray in until fully seated and flush
• If your model uses a separate top grate, transfer and reinstall it on the new tray

This replacement ice bucket stores ice from the icemaker and engages the dispenser drive for smooth dispensing. Swap a cracked or warped bin to prevent leaks, jams, and inconsistent ice dispensing performance. What it does:

• Holds ice produced by the icemaker inside the freezer
• Interfaces with the dispenser drive to move ice toward the chute
• Keeps cubes contained to reduce spills and jams
• Common symptoms: cracked bin, ice not dispensing, bucket won't seat properly, clumping or leaking ice

• 1 ice bucket

• Disconnect power to the refrigerator before servicing
• Empty the old bucket and pull it straight out; avoid forcing the auger/drive area
• Align and seat the new bucket so the rear hub fully engages the drive coupler
• Restore power and test ice dispensing; the bucket is fully latched and stable

This slide rail mounts inside the refrigerator and guides a storage drawer so it opens and closes smoothly. Replacing a worn or broken rail restores proper drawer alignment and easy access to stored items. What it does:

• Supports the drawer and provides a smooth glide path along the cabinet wall
• Maintains alignment to keep the drawer level and on track
• Replaces cracked, warped, or worn rails that cause rough, uneven movement
• Common symptoms: drawer binds or sticks, tilts or sags, falls off track, or shows visible rail damage

• 1 slide rail

• Disconnect power to the refrigerator before servicing interior components
• Remove the drawer and any shelf/glass cover to access the rail
• Save and reuse existing mounting screws and any end caps/brackets; match the rail's orientation to the original if your model uses left/right rails
• Align the new rail with factory mounting points, tighten screws, and test for smooth operation

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

This vegetable tray assembly provides the removable tray used in the refrigerator crisper area to support and separate produce. It restores a stable, easy-to-clean surface so drawers slide and store fruits and vegetables properly. What it does:

• Replaces a cracked, warped or missing crisper tray that supports produce in the refrigerator
• Restores a flat surface so fruits and vegetables sit securely and drawers close properly
• Helps maintain proper airflow and containment in the crisper area for typical produce storage
• Visible damage or a tray that no longer seats can cause items to fall or interfere with drawer operation

• Remove all food and the crisper drawer before installing; work on a clear, protected surface
• Align tray with the existing tracks or guides and slide into place until it seats
• Handle carefully to avoid chips or cracks if the tray is glass or brittle plastic
• Unplug the appliance or disconnect power first and follow all safety precautions

This blower cover mounts over the dishwasher's drying fan/vent opening to shield the blower and direct air into the tub. Replacing a damaged or missing cover helps maintain proper airflow and supports consistent drying performance.

• Protects the blower assembly from splashes and debris
• Channels air into the tub during the dry cycle
• Helps maintain the vent seal to limit moisture escape
• Common signs it's needed: poor drying results, rattling near the vent, visible cracks/warping, or moisture around the vent area

• Disconnect power and turn off water supply before servicing
• Access from inside the tub; remove racks if needed
• Note screw locations and any seal orientation; seat the cover evenly and tighten screws snugly without overtightening
• Run a short cycle to check airflow and inspect for leaks

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks

Color: blue. Measures about 2-1/2 inches wide by 4-1/2 inches deep.

This decor assembly is the outer trim that surrounds the appliance control panel, restoring the unit's finished appearance and protecting the controls from everyday wear. It replaces cracked, scratched or faded trim to make the front look like new. What it does

• Covers and protects the control area from spills, scratches and cosmetic damage
• Restores the appliance's factory appearance after impact or deterioration
• Helps keep buttons and touch controls clear of debris and grime
• Required to properly seat or secure the control components it surrounds

• One decor assembly (control-panel trim) as pictured

• Disconnect power (unplug or shut off breaker) before starting work
• Remove any retaining screws or clips from the control panel; handle trim gently to avoid breaking tabs
• Reuse existing fasteners unless new hardware is explicitly listed as included

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power