Lg Parts

The Tine Row Holder is an OEM part for LG dishwashers. It is a molded plastic bracket located inside the dishwasher that firmly holds the horizontal tine rows of the upper spray arm assembly in place. Subject to vibrations during the wash cycle, the tine row holder must securely grip this assembly.

Symptoms of a bad tine row holder include:

• Loosened or detached upper spray arm that causes insufficient washing 
• Rattling noises from loose components inside the tub 
• Potential leaks if the plastic material cracks fully over time

Causes of failure can include cracking of the holder plastic from solvent exposure and mineral buildup over thousands of wash cycles. Replace with this OEM LG part to ensure balanced water distribution to all areas of dishes. It is also compatible with Sears/Kenmore dishwasher models.

Dryer stops mid-cycle or won't start? This door latch assembly secures the door to keep your dryer running. Simple 2-minute DIY fix for most models.

Fixes washer that won't spin or makes grinding noises during spin cycle. This rotor assembly mounts on the motor and works with the stator to turn the drum.

Mounts the door hinge to your washer's front cabinet. Replace if bracket is bent, broken, or missing to restore proper door alignment and sealing.

Fix error code Er FF or overheating issues with this DC condenser fan motor. Circulates air across condenser coils to maintain cooling. Video guide available.

Mounting bolt for washers. Secures internal components and assembly parts. Replace if bolt is stripped, corroded, missing, or damaged during repairs.

Pressure regulator assembly for gas ranges. Mounts to the gas supply line to control fuel pressure. Replace if cracked, leaking, or damaged.

The DC pump motor assembly powers the pump that moves water through your appliance. Replacing a worn motor helps restore proper water flow so cycles can complete and reduces issues like standing water and excessive noise.

• Drives the pump impeller to move water for draining or circulation, as designed by the appliance
• Supports proper cycle completion by clearing water from the tub or sump
• Common symptoms of a failing motor include standing water, incomplete draining/circulation, loud humming or grinding near the pump, or cycle errors
• May run intermittently, stall, or overheat as internal components wear

• Disconnect power and turn off the water supply before servicing
• Expect residual water; protect the area with towels or a shallow pan
• Note wiring connectors and hose routing; transfer any brackets, grommets, or seals from the original as needed
• Secure hose clamps and test for leaks while running a brief test cycle

Gas valve assembly that controls and delivers gas to the burner. Mounts inside the range cabinet. Replace if cracked, leaking, or damaged to restore safe gas flow.

Burner cap sits over sealed burner units to direct flame upward. Replace if cracked, chipped, or damaged from wear. Lifts off easily for quick replacement.

This connector joins two sections of the refrigerator's water tubing to create a secure, leak-resistant seal. Replace a cracked or loose connector to restore proper water flow to the dispenser and ice maker.

• Provides a sealed union between two water tubes in the appliance's water system
• Helps prevent air and water leaks that can impact dispenser and ice maker performance
• Typical failure signs include drips or puddles near the connection, visible seepage, or moisture alerts
• Also causes low/no dispenser flow or small or hollow ice cubes

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Prepare tubing with a clean, square cut; insert each tube fully into the connector until seated, then pull-test to retention
• Restore water and check all joints for leaks; purge air by dispensing water before normal use

If your refrigerator light stays on or interior won't cool properly, the door switch may have failed. This magnetic switch detects door position.

Seals the door opening to the outer tub on front-load washers. Replace if you notice leaks, tears, odors, or clothes snagging. Confirm fit with your model.

Oven not heating or baking unevenly? A failed bake element is the most common cause. This part provides the primary heat source for baking and roasting.

Shallow deli drawer for storing meats and cheeses in your refrigerator. Replace when cracked, broken, warped, or missing to restore organized storage.

This decor assembly is the outer trim that surrounds the appliance control panel, restoring the unit's finished appearance and protecting the controls from everyday wear. It replaces cracked, scratched or faded trim to make the front look like new. What it does

• Covers and protects the control area from spills, scratches and cosmetic damage
• Restores the appliance's factory appearance after impact or deterioration
• Helps keep buttons and touch controls clear of debris and grime
• Required to properly seat or secure the control components it surrounds

• One decor assembly (control-panel trim) as pictured

• Disconnect power (unplug or shut off breaker) before starting work
• Remove any retaining screws or clips from the control panel; handle trim gently to avoid breaking tabs
• Reuse existing fasteners unless new hardware is explicitly listed as included