Lg Parts

This inlet hose delivers fresh water from your home supply to the appliance, restoring proper fill and preventing leaks. It's a direct-fit replacement designed to restore normal water flow and stop visible hose damage. What it does:

• Channels water from the household supply into the appliance's inlet valve
• Replaces cracked, split, or leaking inlet hoses that allow water to escape
• Helps resolve symptoms like weak/no fill, visible dripping at the connection, or intermittent water flow
• Matches OEM routing and connection points for a proper seal when installed correctly

• Turn off water supply and unplug the appliance before starting
• Inspect fittings and replace any damaged seals or washers as needed
• Hand-tighten connections and finish with a quarter turn; avoid overtightening to prevent damage
• Run a short test fill and check all connections for leaks before returning the appliance to service

This inlet valve assembly controls the flow of water into the washer so cycles fill correctly and on schedule. A direct-fit replacement that restores proper water delivery and helps prevent overfilling or no-fill conditions. What it does:

• Opens and closes to allow cold and hot water into the tub during fill cycles.
• Responds to the washer's control signals to deliver the correct water amount.
• Commonly replaces a valve that leaks, won't fill, fills slowly, or causes continuous filling.
• Helps resolve related error codes or fill/level issues when caused by a faulty valve.

• Disconnect power and shut off both water supply lines before starting work.
• Drain remaining water from hoses and use caution when handling connectors.
• Inspect inlet hoses and seals; replace damaged hoses or seals to prevent leaks.
• After installation, restore water and power, then run a short test cycle to check for proper fill and leaks.

This NTC thermistor is a refrigerator temperature sensor that monitors cooling system temperature and helps the control board maintain proper operation. It replaces a failed sensor to restore accurate temperature sensing and reliable cycle control. What it does:

• Measures internal temperature and sends a changing resistance signal to the control board
• Helps the fridge adjust compressor/fan cycles for stable cooling
• Common symptom fix: erratic or incorrect temperatures, frequent cycling, or temperature-related error codes
• Works as the sensor used in evaporator/air temperature sensing circuits (model-dependent)

• One NTC thermistor sensor (wiring and connector as shown)

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor and wiring gently; avoid kinking or stretching the lead wires
• Mount and route the sensor per the unit's service diagram so it contacts the intended location
• Verify sensor response with a multimeter (NTC resistance should change with temperature) or follow the manufacturer's service procedure

This power control board assembly replaces the sub power PCB that manages voltage and signal distribution to the appliance's main controls. Restores control reliability and resolves power-related control issues when the board is at fault. What it does:

• Routes power and control signals between the main control and subsystem components
• Helps the appliance respond correctly to control inputs and cycles
• Commonly replaces a board that causes no power to portions of the appliance or erratic electronic behavior
• Addresses symptoms such as control panel unresponsiveness, intermittent operation, or error codes tied to power/control faults

• Disconnect power before attempting any repair to avoid shock or damage
• Handle the PCB by its edges and avoid static discharge; use proper ESD precautions
• Installation requires basic hand tools and involves removing panels and connectors; keep track of fasteners and wiring
• Replace only with the exact part number to ensure proper fit and function

This PCB power control board is the main electronic control that manages appliance functions and power distribution. Replacing a failed board restores proper control and helps resolve electronic and power-related faults. What it does

• Controls and coordinates appliance functions by processing user inputs and sending signals to motors, valves, heaters, and displays
• Manages power distribution to subsystems and protects against erratic electrical behavior
• Common symptoms of a failing board: appliance won't start, intermittent operation, unresponsive controls, or error codes tied to electronic control
• Replacing the board often resolves communication faults and loss-of-function related to the main control electronics

• One PCB power control board assembly (as shown)

• Disconnect power before starting; risk of electric shock if power is not isolated
• Handle the board by its edges and avoid touching components or connector pins to prevent static damage
• Verify connector alignment and seating; do not force connectors—confirm match to the wiring harness

This controller assembly is the main electronic control board that manages your appliance's cycles and user interface, restoring normal control when the original board fails. It replaces a faulty control module to help the unit operate reliably. What it does:

• Controls timing, cycles, and functions per user commands and sensor inputs
• Replaces malfunctioning or unresponsive control electronics that cause erratic operation
• Can resolve symptoms such as no power to controls, unresponsive buttons, or incorrect cycle behavior
• Works with existing wiring harnesses and display components when compatible

• Disconnect power before beginning work to prevent shock or damage
• Verify connector locations and orientation before removing the old board
• Handle the board by edges and avoid contact with circuitry to prevent static damage

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

This sheath heater assembly supplies the heating element used to warm air in the dryer, restoring proper drying performance when the original element fails. It's a direct-replacement part that fits into the dryer's heater housing. What it does:

• Heats incoming air so the dryer can remove moisture from clothes
• Replaces a damaged or open heating element that prevents the dryer from producing heat
• Addresses symptoms like no heat, long drying times, or intermittent heating
• Works with the dryer's thermostats and safety devices to regulate temperature

• Disconnect power (and gas supply if applicable) before beginning work
• Allow the appliance to cool and drain any stored energy before touching internal components
• Handle the heater carefully to avoid bending or damaging the element or terminals
• Check thermostats, thermal fuses, and wiring for related faults when replacing the heater

This customized screw secures specific appliance components to maintain proper fit and prevent parts from loosening during normal use. Use it when replacing a missing or damaged fastener to restore secure assembly and reduce vibration. What it does:

• Fastens panels, brackets, or components to the appliance frame
• Keeps parts aligned to prevent rattling or movement during operation
• Replaces stripped, missing, or damaged screws that cause loose assemblies
• Helps maintain electrical and mechanical connections by holding parts in place

• Disconnect power and water before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or crack plastic
• Keep removed hardware organized for reassembly; replace any additional damaged fasteners

A factory screw for securing specified components in your appliance. Replaces a missing or damaged fastener to restore a tight, reliable hold and help reduce vibration, rattling, and misalignment.

• Secures brackets, covers, or internal assemblies where this exact screw is specified by the manufacturer
• Useful when the original screw is missing, stripped, or corroded
• Helps eliminate looseness, vibration, and rattling noises
• Matches the original fastener for proper fit and thread engagement

• Disconnect power (and shut off water supply if applicable) before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace any damaged clips or inserts to ensure a secure repair

This inner door frame is the interior support trim that helps secure the door assembly and provides a finished surface inside the appliance door. It restores proper fit and a clean appearance when the original frame is cracked or damaged. What it does:

• Provides structural support for the inner door panel and helps hold components and liners in place
• Restores proper alignment so the door closes evenly and seals correctly
• Replaces cracked, warped, or broken frame sections that can allow rattling or gaps
• Helps maintain the correct interface between the door and the gasket to prevent airflow issues

• Disconnect power to the appliance before beginning any repairs.
• Removal typically requires taking off the door trim or liner and using basic hand tools; keep fasteners organized.
• Handle the frame and door panels carefully to avoid scratching or bending other surfaces.

This drum roller supports the dryer drum so it spins smoothly and quietly. Replacing a worn roller restores stable drum rotation and helps reduce rubbing, scraping or thumping noises during operation. What it does:

• Supports and guides the dryer drum for even, stable rotation
• Reduces friction and drum wobble that can cause noisy operation
• Helps the drive belt track correctly and maintain proper drum alignment
• Common symptom: squeaking, thumping, or rubbing sounds and uneven spinning

• Disconnect power before starting any repair
• Remove the dryer drum or access panel to inspect and replace the roller; support the drum while removing/reinstalling
• Check other drum rollers, bearings and the drive belt for wear and replace as needed to prevent repeat failure
• Reassemble carefully and test with the dryer empty to ensure smooth, quiet rotation

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This duct outlet directs a dryer's exhaust from the cabinet to the external vent, helping maintain proper airflow and reduce leaks. It replaces a damaged or worn outlet flange to restore safe venting. What it does:

• Channels dryer exhaust from the cabinet to the vent hose or duct
• Helps maintain proper airflow for efficient drying
• Prevents exhaust leaks that can cause poor performance or odors
• Reduces rubbing/interference that can create noise when damaged

• One duct outlet

• Disconnect power before servicing; for gas dryers, turn off the gas supply and disconnect per local codes
• Use basic hand tools; avoid bending the outlet flange to prevent cracks
• Verify a secure seal with the vent hose after installation and test operation

Note: Lamp and socket assembly. For lamp only, order 6913EL3001E.

A replacement control knob assembly that restores reliable control and user interface for compatible appliances. Designed to give a secure fit and clear detents for accurate temperature or function selection. What it does:

• Replaces a worn, cracked, or missing control knob to restore knob-to-shaft engagement
• Provides positive detents and tactile feedback for accurate setting selection
• Helps stop slipping or spinning knobs that prevent proper control
• Matches original mounting for a straightforward fit

• One knob assembly

• Turn power off to the appliance before beginning any repair to avoid shock or injury
• Remove the old knob by pulling straight off the shaft; align replacement on the shaft and push firmly until seated
• If the knob doesn't seat, confirm shaft style (splined, D-shaft, or round with adapter) and part compatibility