Fuse Or Sensor

Dryer won't heat or overheats? This high-limit thermostat opens the heating circuit at preset temperatures to prevent overheating and restore safe operation.

Microwave won't start or stops mid-cycle? A blown fuse is often the culprit. This 5 amp fuse protects your microwave's electrical system. Quick DIY fix.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

Dryer won't start or stops mid-cycle? A blown thermal fuse is often the cause. This safety component cuts power when temperatures get too high.

Range won't heat or shuts off unexpectedly? A faulty thermal fuse may be the cause. This safety component protects against overheating. DIY repair.

Oven overheating or won't heat properly? This safety thermostat monitors backguard temperature to prevent overheating. Simple DIY fix restores safe operation.

The Moisture Sensor is an OEM component specifically designed for Whirlpool washing machines. The sensor monitors moisture levels to determine when the appropriate moisture point has been reached, signaling the appliance to advance to the next step in the cycle.

Symptoms of a bad moisture sensor include: 

• Inability to advance through entire wash cycle  
• Immediate ending of cycle after short period of time
• Sensor may show moisture levels incorrectly
• LED lights indicating error codes related to moisture detection

Causes of a bad moisture sensor can be due to cracks, corrosion, or damage to its sensitive electronic components from impact or overuse. Regular cleaning and maintenance helps extend the life of the moisture sensor. 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Oven won't heat or shuts off after preheating? This thermal cutoff fuse opens the heating circuit when temperatures exceed safe limits. Direct fit part.

Fixes a microwave that won't heat or start. This thermal fuse protects your microwave from overheating. Direct-fit part for multiple models.

 The Thermostat is an OEM part for Whirlpool microwaves. It is a temperature-sensitive component that monitors heat levels inside the oven cavity during operation.

Causes may include damage from exposure to moisture or debris over time that disrupts accurate readings.

Symptoms of a faulty thermostat include:

• Incomplete or inconsistent heating with uneven hot/cold spots
• Food not reaching expected doneness after preset times
• Overheating errors or cycle interruptions

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Fix inaccurate temperature readings or inconsistent cooling cycles in your air conditioner. This thermistor sensor monitors internal temperatures.

Fix a microwave that won't heat or start with this thermal cutout fuse. This safety component prevents overheating. Takes 30-45 minutes to install.

This thermal cut-out is a temperature-sensing safety device that helps protect the refrigerator's defrost/heater circuit by opening the circuit when temperatures exceed safe levels. It prevents overheating and helps maintain normal defrost cycles. What it does:

• Senses temperature in the defrost/heater area and opens the circuit to stop heating if temperatures get too high
• Prevents overheating of defrost heater or related components
• Can cause defrost failure symptoms when faulty, such as excessive frost buildup or poor cooling
• May also contribute to long run-times or irregular defrost cycles when not operating correctly

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the part and wiring gently; ensure correct orientation and secure connections per service manual
• Use the exact replacement part number for compatibility