Washer Spring Parts

This spring restores tension to the door lock mechanism so the latch returns to its proper position after operation. A worn or missing spring can cause a loose latch, difficulty locking, or a door that won't stay secured during a cycle.

• Returns the door lock latch to its resting position
• Helps ensure the door locks securely during operation
• Symptoms can include a floppy/loose latch, intermittent lock errors, or door not staying latched
• Also helps resolve issues where the door won't unlock smoothly

• Disconnect power before servicing
• Access the door lock assembly per your model's service procedure
• Note spring orientation during removal; install the new spring in the same positions
• Latch operation by gently opening/closing the door before reassembling

This door spring counterbalances your dishwasher door so it opens and closes smoothly without slamming. Replacing a fatigued or broken spring restores proper tension and helps protect the hinges and latch.

• Provides counterbalance tension to the door through the hinge mechanism
• Helps the door open and close with controlled movement and stay in position
• Symptoms of failure can include a door that drops quickly, feels heavy, or won't stay put
• May also cause popping/squeaking noises or uneven action on one side of the door

• Disconnect electrical power and turn off the water supply before servicing
• Remove the toe panel/kick plate to access springs near the hinges
• Carefully relieve and reattach spring tension; wear gloves and eye protection
• Ensure both sides are tensioned evenly after replacement

This is a suspension spring for select washers. It supports and stabilizes the wash tub during spin and agitation to reduce vibration and noise, helping the machine run smoothly.

• Supports the tub within the cabinet to control movement
• Helps reduce excessive vibration, banging, or walking during spin
• Addresses symptoms like out-of-balance loads, noise, or shaking
• Loss of tension, stretching, or breakage can require replacement

• Unplug the washer and shut off water supply before repair
• Access typically requires removing the top or front panel; support the tub to relieve spring tension
• Wear gloves and eye protection; springs are under tension
• Replace any damaged or missing suspension components in pairs or as required.

Idler lever spring (with silencer) restores proper tension to the dryer idler assembly so the drive belt tracks and runs smoothly. Replacing a worn or broken spring can reduce noise and help prevent belt slippage. What it does:

• Provides tension to the idler lever so the drive belt maintains correct tracking.
• Helps prevent belt slipping that can cause uneven drum rotation or failure to tumble.
• Can reduce squealing, thumping, or rattling coming from the idler/drive area.
• Works as the replacement tension spring for the idler lever assembly when the original is damaged or lost.

• Disconnect power (and gas if applicable) before starting any repair.
• Access typically requires removing dryer panels and/or the drum; follow the model-specific service manual or OEM instructions.
• Inspect the idler pulley and drive belt while replacing the spring; replace any worn components.

Damper shock (60N) for washers. This shock absorber steadies the outer tub during spin to reduce vibration and noise. Replacing a weak damper restores smoother operation and helps prevent the basket from banging the cabinet. What it does:

• Mounts between the outer tub and base to absorb movement
• Controls vibration for a stable spin cycle
• Worn or broken dampers can cause loud banging/thumping, excessive shaking, or the washer "walking"
• Visual clues of failure may include cracked ends, loose mounts, or oil residue on the shock body

• Disconnect power and shut off water before servicing
• Remove the appropriate access panel(s) and support the tub to relieve tension on the shock
• Match the original orientation and transfer any brackets or hardware as needed
• After installation, hand-move the tub to verify smooth travel; consider replacing all shocks together for balanced damping

This suspension stabilizes the washer tub to reduce excessive movement and vibration during spin cycles, helping the washer run quieter and more smoothly. What it does

• Supports and centers the washer tub to prevent excessive rocking during operation
• Dampens vibration and reduces noise caused by an imbalanced load
• Helps maintain proper drum alignment for reliable spinning and draining
• Worn or damaged suspension can cause loud noise, heavy vibration, or excessive movement

• One suspension (single tub support) as shown

• Disconnect power and water supply before beginning any repair
• Support the tub/drum before removing the old suspension to prevent sudden movement
• Inspect other suspension components and mounting hardware; replace any worn parts for balanced performance

Drum shock absorber for front-load washers. This damper connects the tub to the chassis and controls movement during wash and spin, reducing vibration and noise so the washer can ramp to proper spin speed without banging.

• Damps and stabilizes the drum to control vibration during acceleration, spin, and coast-down
• Helps reduce shaking, banging, and "walking" across the floor
• Can help address out-of-balance messages and noisy operation
• Worn shocks may leave loads wet after spin or cause loud thumping

• Disconnect power and shut off water before servicing; move the appliance to access panels safely
• Access the shock from the front or rear per model; support the tub to relieve tension
• Note pin/bolt orientation; transfer any reusable hardware and fully seat both ends of the new shock
• Consider replacing them as a set for balanced damping; run a short test cycle to verify stability

This washing machine shock absorber stabilizes the outer tub during wash and spin. Replacing a weakened damper helps control vibration and noise so the washer runs smoother and is less likely to shake, bang, or walk.

• Mounts between the tub assembly and cabinet/base to cushion movement
• Helps prevent excessive vibration, shaking, and thumping noises
• Can reduce "walking" or out-of-balance interruptions when a damper is worn
• Supports smoother, quieter spin performance

• Disconnect power and turn off water supply before servicing
• Remove the appropriate access panel(s) to reach the dampers
• Support the tub when removing mounting pins/bolts; match the original orientation
• Inspect all dampers; replace any that show wear for balanced performance

This hinge spring restores proper tension to the door so it opens and closes smoothly and stays aligned. Replacing a fatigued spring helps prevent sagging or slamming and supports a consistent, reliable door close.

• Provides the return tension/counterbalance for the door hinge mechanism
• Assists smooth opening/closing and helps the door stay properly aligned when latched
• Helps maintain consistent closing force over time
• Failure symptoms include: door drops quickly, won't stay aligned or fully closed, weak/squeaking spring action

• Disconnect power before service; allow any hot surfaces to cool
• The hinge and spring are under tension—support the door and release/install tension carefully
• Note spring orientation and hole positions before removal; match them on installation
• Access may require removing trim or the door; keep fasteners organized for reassembly

This replacement tension spring restores proper return and tension for a Speed Queen laundry component, helping moving parts operate smoothly and quietly. Fits select models — used where a small coil spring provides return force. What it does

• Provides return/tension force for a moving component (door, lever, or linkage) to hold proper position.
• Helps reduce rattling, sticking, or loose movement caused by a worn or broken spring.
• Restores reliable mechanical action when the original spring has stretched, broken, or come off.
• Small, coil design suitable for use where compact tension is required.

• One replacement spring.

• Disconnect power to the appliance before servicing; follow safe lockout procedures.
• Handle under tension carefully; use pliers or spring tool as recommended in the service manual.
• Inspect adjacent clips, pins, and mounts; replace any damaged hardware for secure reinstallation.
• Refer to the appliance's service manual or OEM instructions for exact placement and installation steps.

This genuine OEM spring provides the tension needed for the appliance door to open and close smoothly and stay properly seated. It restores reliable door operation and reduces sagging or unlatched door issues. What it does:

• Applies tension to the door hinge/assembly so the door stays closed and aligns properly.
• Helps the door open and close smoothly without slamming or dragging.
• Reduces wandering, sagging, or a door that won't latch securely.
• Can eliminate popping or squeaking noises tied to a worn or stretched spring.

• One replacement door-tension spring.

• Disconnect power (and water if applicable) before starting any repair.
• Springs are under tension — use caution and appropriate tools/gloves to avoid injury.
• Inspect hinge/retainer hardware and replace any damaged clips or anchors during installation.

This cabinet damper helps control the motion of a refrigerator cabinet or door assembly for smoother, more balanced movement and reduced slamming. It restores the intended counterbalance action when the original damper is worn or broken. What it does:

• Provides counterweight action to help a cabinet or door close smoothly and stay balanced
• Reduces sudden drops, slamming, and uneven door movement caused by a failed damper
• Works as the mechanical balance component within the cabinet/door hinge/damper system
• Commonly replaced when the door feels loose, drops unexpectedly, or does not stay in position

• One cabinet damper as pictured

• For safety, unplug the appliance or disconnect power before beginning work
• Basic disassembly of the cabinet/door trim or hinge may be required; follow OEM instructions
• Verify orientation and mounting location before removing the old part to ensure correct installation

This replacement axle/latch spring secures the latch/axle assembly so the appliance door or panel stays engaged during use. It restores proper latch tension for reliable closing and operation. What it does:

• Applies tension to the latch/axle so the door or access panel stays closed and latched
• Helps ensure the appliance detects a closed door and will start or run normally
• Common symptom: door won't stay closed or latch feels loose or fails to engage
• Small metal spring designed for a specific latch assembly — not a universal part

• Disconnect power to the appliance before starting any repair
• Access may require removing a panel, bezel, or door — use proper tools and keep fasteners organized
• Handle the spring and latch components carefully; springs are under tension and can snap free