Washer Switch

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch likely failed. This DIY repair restores proper filling.

Fix a washer that overfills or won't stop filling water. This pressure switch senses water level and signals when to stop. Simple 10-minute DIY repair.

Washer won't fill or overfills? Water level pressure switch senses tub water and controls fill cycles. Restores accurate fill levels and agitation.

Fix a washer button that won't respond, works intermittently, or sticks when pressed. This pushbutton switch restores on/off control for your appliance.

Fix a washer that won't start or respond to controls with this switch assembly. Restores electrical switching in control and safety circuits.

Fix unresponsive or erratic cycle selection with this rotary encoder switch. Mounts behind the control knob to restore accurate cycle settings and indicators.

Color: Black. Instruction sheet included.

Fix washer temperature issues with a new selector switch. Solves problems when hot or cold water won't flow correctly or temperature settings don't respond.

This 3-position temperature switch selects the dryer's heat level so the appliance reaches the desired drying temperature. It replaces a worn or faulty selector to restore proper temperature selection and consistent drying performance. What it does:

• Switches between three temperature settings to control dryer heat levels.
• Routes power to the heater circuit based on the selected heat setting.
• Commonly replaces a switch that causes incorrect heat, no heat on some settings, or inability to change temperature.
• Works with the dryer's control system and thermostats to maintain selected drying temperature.

• Disconnect power to the appliance before attempting any service.
• Handle terminals and connectors carefully; match wiring to original locations or take a photo before removal.
• Verify operation with a multimeter for continuity per service manual before and after installation.

If your washer won't fill, overfills, or leaks water everywhere, the water level pressure switch may have failed. DIY fix in 15 minutes or less.

Washer won't agitate or spin? Lid switch detects when lid opens/closes to control operation. Test for continuity before replacing. DIY-friendly repair.

Fix PE error codes and water overfilling issues with this pressure switch. Monitors tub water level to control fill and drain cycles. 30-minute DIY repair.

This rotary on/off switch controls the dryer's Finish Guard (also called Wrinkle Guard/Wrinkle Shield) feature. Replacing it restores proper control of the post-cycle intermittent tumbling that helps reduce wrinkles, preventing the feature from being stuck on or off.

• Provides 2-position on/off selection for the Finish Guard/Wrinkle Guard function
• Failure can cause the feature not to engage or to stay on after the cycle ends
• Knob may feel loose or fail to click when the switch is worn
• Mounts in the control console and interfaces with the external selector knob

• Disconnect power before servicing
• Access through the control console; remove paneling as needed
• Transfer wires one at a time or photograph connections for reference
• Reinstall using the existing knob and mounting hardware

If your washer won't start or stops mid-cycle, this lid switch assembly detects lid closure to restore safety interlock. DIY-friendly, installs in 15 minutes.

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

This is an electrical relay used in the washer's motor or control circuit to switch power to specific components during operation. It helps regulate the timing and function of the wash and spin cycles. Replace this relay if the washer motor won't start, the machine hums but doesn't agitate or spin, or if cycles fail to advance properly.