Washer Valve

The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more

• No hot or cold water
• Will not stop filling with water
• Will not fill with water
• Leaking

This is my third repair of this type. The first was a stand-alone washer and was very easy, because there was a plate on which the inlet valve assembly was mounted, and it was easily removed. This repair was on a Frigidaire stacked washer/dryer (laundry center). Stacked washer/dryers are typically purchased to save space and are often tucked into a closet. Be sure you can pull it out to access both front and rear. Remove drain hose from drain, detach water hoses, electricity and dryer vent... Read more

The hot inlet valve was dripping water, replaced it. Water and soap were coming out of the vent pipe. The new Float assembly had a shorter shaft than the old Float Assembly I was replacing. I did install the new Float Assembly and cleaned the vent hose where the float seats and I haven't seen any more water on the floor. Both repairs were made easy by watching your repair videos. Read more

Took machine apart replaced valve assembly. Read more

• Will not fill with water
• No hot or cold water
• Will not stop filling with water

I called Appliance pros and asked for a diagnosis. They gave one and sent me the part. It took 15 min. and it worked perfectly. Also got super fast delivery on the part. Thank you!! Read more

I ordered the valve. Watched a video and installed it in 30 minutes. Works perfectly. Read more

Ordered water inlet valve. Took all about 10 mins to change it solved the problem. Easy fix Read more

Called a repair man after not being able to determine the exact problem. Narrowed it down to valves, level switch or mother board. Repairman took money for parts and then said he couldn't find them. Went online and found this site, ordered parts Monday, had them by Thursday noon. Had machine running by 1. Read more

• Will not fill with water

The GE front loading HE washer wound paused at the rinse fill point and need manual selection of drain & spin to finish the load. Online searches told me how to get the error code. Once E22 was found online searching told me it was a water flow problem- slow fill. I removed the hoses at the washer and inspected for clogs - nothing was found. I then put the ends of the hoses in a bucket and turned on the water- strong flow. Interesting is some debris/solids came out. I’m betting over time solids... Read more

Water became visible as it accumulated at the bottom rear part (the part that is tilted back) of the washer drum. I theorized that the valve controlling water flow into the machine was to blame. I began my troubleshooting by going to Appliance Pros website where I looked for a Water Inlet Valve. I easily found this on the exploded parts diagram. After identifying the part that seemed to be the issue, I began reading other reviews from folks who were experiencing the same problem and who solved... Read more

Remove the two valves at back of washer, only 4 screws, remove the electrical clamps, replace with valves, easy, 20 minutes to fix, and a woman did it, saved $320.00, yahoo Read more

• Will not stop filling with water
• No hot or cold water

Appliance Parts Pros I've used in the past and will continue to use, now they have a video showing step by step how to change the part your going to purchase, video also explains what the part does and symptoms of bad existing parts like mine. Washer machine was dripping water into tank when not in use, it was the water inlet valve. I purchased on a Sunday and it arrived with our mailman on Wednesday. I watched the repair video one more time and changed it out. When you unhook hoses to remove... Read more

Replaced the broken parts with new ones. Read more

Changed the water valves. Read more

• Will not drain

Pulled dishwasher from the cabinet and flipped onto its side. Easy access to sump and drain flapper valve that I also replaced. Rubber sump coming apart into soft pills & chunks and plugging spray arms. Better now but it's rediculous that GE would make components that dissolve this way. Read more

Removed the front panel and removed the screw from the console which revealed a broken plastic tab on the right side of the old injector. Replaced the old injector with the new one and that took care of the problem. Read more