Need Help?
Call
By GE. Fits many different washer brands and models. Includes insert.
The new GE washers come with a fill valve that has a 1/8" hole for the hot water inlet. This is probably for energy savings or something. So, I installed the older style GE fill valve on my new machine. Since the older style has larger inlet holes for both hot and cold water, it fixed my problem easily. NOTE: The outlet nipple on the new style GE fill valves are larger than the older style. Therefore, I had to make a coupling piece to attach the older style GE valve outlet nipple to the... Read more
Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.
Removed some screws, opened the top of the wash machine, unplugged some wires to remove the part, plugged the wires back into the mew part, put the new water valve into place, secured the water valve with the screw, put the top back on the wash machine, and replaced all remaining screws! Real Simple! Read more
Fix washer filling when off or showing E11 error with this water inlet valve. Controls hot and cold water flow. Moderate DIY repair, 1-2 hours.
Removed the top of the washer, located the fractured water valve, removed the broken water valve and replaced it with the new valve. Read more
This diverter valve directs wash water inside the machine, switching flow between internal paths during wash and drain/recirculation steps. Replacing a failed diverter restores proper water routing so cycles advance and complete as designed.
I replaced the door seal for the leak. We had a small tear in the sealing surface that resulted in water dripping down the front of the machine (just below the door). I also replaced the detergent dispenser main box with diverter unit. This corrected excessive water being left inside the detergent dispenser at the end of each cycle. I highly recommend replacing the dispenser seal and gasket nozzle to be on the safe side. As these parts are subject to wear and fatigue over the life of the... Read more
This valve magnet is the solenoid actuator used to open and close a dishwasher water/control valve, restoring proper water flow for filling and cycle operation. It replaces a failed or weak magnet to help the valve respond correctly. What it does:
The repair is easy. Two screws in the back hold the top cover - once they are off you need to slide the cover back and it comes off. The valve is right there where the cold water hose is connected. Disconnect the control wires / clamp and slide back the wire clamps / remove the two rubber hosed / remove the old valve (it is snapped in place - look at the new one to understand the snap mechanism) / install the new valve. The repair takes less than 10 min. I tested and sure enough... now it... Read more
This is an electrically controlled water inlet valve that regulates the flow of hot and cold water into the washing machine tub during fill cycles. It opens and closes in response to signals from the control board to deliver the correct water temperature and volume. Replace this valve if the washer is not filling with water, filling slowly, leaking from the back, or continuing to fill when it should stop.
I put in a new water valve Read more
Fix a washer that won't fill, fills with wrong temperature water, or overflows. This water inlet valve controls water flow. Easy DIY repair in under 1 hour.
Replaced Water Valve Assembly. One of the easiest repairs I've ever done. Read more
Fix washer leaks, overfilling, or no water flow issues. This 3-way inlet valve controls water routing to wash and dispenser. Simple DIY repair in 15-20 min.
I changed the water inlet (3 way). Now my washing machine working properly with fabric softener. The parts i order is a next day delivery. Thanks appliace partspros. Read more
New seals come with this valve.
Sediment from water line had restricted flow through dispenser valve causing insufficient flow to flush fabric softener. Replaced dispenser valve. Also replaced main water valve as preventive maintenance given they are easily replaced together. Read more
This water valve kit regulates the flow of hot and cold water into your appliance during fill. Replace a weak, leaking, or stuck valve to restore consistent fills and proper shutoff, resolving common no-fill, slow-fill, or seeping issues.
Removed old water valve and replaced it with new one. Reconnected wiring and water lines. Everything is working fine now. Read more
This water inlet valve controls the flow of hot and cold water into your washing machine during fill cycles. It opens and closes electronically in response to signals from the control board to deliver the correct water temperature and volume. Replace this valve if your washer won't fill with water, fills slowly, leaks from the back, or continues to fill when it shouldn't.
Replaced the solenoid controlled water valve. Read more
Fix continuous water flow or won't-stop-filling issues with this washer hot water inlet valve. Controls hot water during fill cycles. DIY-friendly, 30-minute repair.
After researching on line I was able to narrow down the problem to either the cold water of hot water fill valve. These valves are electronically controlled and can go bad thus causing the washing machine to not fill properly. Nf stands for "no fill". I replaced the cold water valve first which was held by two screws and a couple of wires. It literally took me 5 minutes to replace the part. As soon as I started the wash cycle I could tell I had fixed the problem because the humming noise that... Read more
Fix washer that won't fill, shows OE/NF error, or keeps running water even when off. Cold water inlet valve replacement takes 5-10 minutes with basic tools.
Fix washer not filling, slow fill, or LF error codes. This water inlet valve controls water flow into your washer. Moderate DIY repair, 30-45 minutes.
REPLACED ENTIRE WATER CONTROL SYSTEM. Being quite anal about my planning projects, I played a Youtube video about this job. I screen captured the important steps, printed them out and taped above the washer. It was a good approach because it gave me a valid reference of the wiring harness reinstallation. Overall, the project was easier than I thought. Great results. Momma is pleased and is no longer complaining that we have to buy a new $1,000 washer ! Read more
Fix a washer that leaks, overfills, or won't fill properly with a new triple water inlet valve. DIYers report 10-15 minute installations.
Watched your repair video and replaced valve in 15 minutes. Read more
This replacement water inlet valve controls the flow of water to the appliance's dispenser and ice-making components, restoring normal fill and preventing supply interruptions when a valve fails. What it does
Thanks to Appliance Parts Pros® I was able to replace that old water valve drip with a new valve. Simply unplug power cord, turn off water, disconnect hoses from machine, with front off machine and top unscrewed, tilt top back and unplug wires to old valve remove screws holding valve from back of machine, remove small hose from old valve to top ring and replace if worn. Then just attach wire harness to new valve, screw valve to back using old screws (2), attach hose to top ring, close top of... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.