Wire, Harness, Power Cord

This harness module is a factory-style wire harness assembly that routes power and control signals between the appliance control and service components, restoring reliable electrical connections and proper control operation. What it does

• Connects the main control board to heating elements, sensors, igniters or switches so commands and power reach working components
• Restores interrupted circuits caused by damaged or burned wires and faulty connector terminals
• Helps eliminate intermittent operation, unresponsive controls, or parts that fail to receive power
• Can resolve symptoms such as no-heat, burners/oven not responding, or error codes linked to open/shorted harness circuits

• Disconnect power to the appliance before servicing to avoid shock or damage
• Compare the harness to the old part and follow the appliance wiring diagram for correct routing and connector placement
• Inspect connector terminals and mating parts for damage before installation; replace any damaged clips or fasteners
• Secure the harness away from heat and moving parts and verify function before reassembling the appliance

This harness jump is a short jumper wire assembly used to reconnect two electrical terminals, restoring an intended circuit path for proper operation. It offers a direct, serviceable way to replace a broken or missing factory jumper. What it does:

• Bridges two terminals to complete a circuit when the original jumper is damaged or removed
• Helps restore power or signal to control components that rely on the jumper connection
• Commonly used in control, terminal block, or switch assemblies where a short wire link is required
• Can resolve symptoms such as intermittent or no power to a circuit, or a component not receiving a control signal

• One harness jump (single jumper wire assembly)

• High-level replacement only; ensure power is disconnected at the breaker or unplug the appliance before servicing
• Match connector style and terminal orientation to the original jumper before installing
• Inspect surrounding wiring and terminals for damage or corrosion; replace if needed

The Power Cord is an OEM part for GE washers. It provides the crucial connection, transmitting electrical current from the wall outlet to power the washer components and functions. Ensuring the integrity of this cord is vital for safe and reliable operation. 

Symptoms of a bad power cord include:

• Frayed, cracked, or exposed copper wiring 
• Loose connections at either end
• Buzzing, sparks, or shocks felt around the cord
• The washer fails to power on as expected

Causes can be normal flexing wear over thousands of cycles, damage from pinching, rodents, or excess tension on the cord. 

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Power Cord is an OEM part for Whirlpool dishwashers. This kit provides you with all the necessary parts to safely and effectively connect your dishwasher to the power source. The kit includes one power cord with a right angle head, one grommet, and one metal strain relief. The power cord with a right angle head allows for easy installation and helps to prevent excessive bending or damage to the cord.  

A bad power cord can occur due to wear and tear, exposure to heat or moisture, or accidental damage. If you notice symptoms such as intermittent power supply, sparks or electrical arcing, or a loose connection, it may be time to replace the power cord kit.

Symptoms of a bad power cord include:

• Intermittent power supply
• Sparks or electrical arcing
• Loose connection

Restore your Whirlpool dishwasher by replacing the faulty or damaged power cord kit with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This intermediate freezer wire harness restores reliable electrical connections within the freezer section. It bridges the cabinet wiring to freezer components so they receive the power and control signals needed for consistent operation and dependable cooling performance.

• Provides a secure, plug-in connection between the main cabinet harness and freezer components
• Replaces harnesses with broken conductors, brittle insulation, or heat-damaged connectors
• Can help when freezer components have intermittent or no power, or when visible wiring/connector damage is present
• Maintains correct routing and strain relief to reduce chafing and shorts

• Disconnect power and wear cut-resistant gloves before servicing
• Photograph connector locations and wire routing for reference during reassembly
• Route the new harness along the original path; secure in existing clips/ties and avoid pinching or stretching wires
• Fully seat each connector until it latches; restore power and test operation

This wire harness routes power and signals between key components for consistent performance. Replacing a damaged harness restores reliable connections and correct operation of affected controls, motors, or sensors.

• Distributes electrical power and control signals between boards, switches, sensors, and motors
• Replaces cut, brittle, burned, or corroded wires and terminals that cause connection faults
• Common symptoms include intermittent operation, a component that won't run, or error codes related to poor connections
• Restores proper wire routing when installed in the factory path and secured with clips/ties

• Disconnect power before servicing; turn off water or gas supply if applicable
• Photograph and label existing connections; move plugs one at a time to the new harness
• Route along the original path; secure in clips/ties and keep clear of sharp, hot, or moving parts
• Seat each connector fully by the plug body (do not pull on wires); inspect mating terminals for heat damage

This 4-foot, 4-wire, 50-amp range cord provides a secure connection from a 4-prong receptacle to your electric range, restoring reliable power when the original cord is damaged, overheated, or worn.

• Connects the range to a compatible 4-prong outlet using two hot, one neutral, and one ground conductor
• Replaces cords with frayed insulation, scorched or loose plug blades, or damaged terminals
• Helps address intermittent power loss or breaker trips linked to a failing cord
• Supports installations that require a 50-amp, 4-wire connection

• Turn off power at the service panel before starting any work
• Route through a proper strain relief and tighten per your model's instructions; connect L1, L2, Neutral, and Ground securely with no exposed copper
• If your model uses a neutral-to-chassis bonding strap, follow the wiring diagram for a 4-wire setup.

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching

This AC freezer harness routes power and signal connections between the freezer compartment components to restore proper electrical continuity and reliable operation. It's a direct-fit wiring harness used in the freezer section of compatible refrigerators. What it does:

• Provides power and signal connections for freezer components such as fans, sensors, and control interfaces
• Ensures secure plug-to-plug wiring without splicing or ad-hoc connections
• Commonly replaced when freezer fan, sensors, or controls lose power or show intermittent operation
• Can prevent electrical issues caused by damaged, corroded, or brittle wiring

• Disconnect power to the appliance before starting any repair to avoid shock hazard
• Verify connector orientation and routing before fastening; match OEM wiring paths and clips
• Do not alter or splice the harness; use exact replacement to maintain safety and function