Axle, Roller, Pulley Parts

Support roller kit for range storage drawers. Replaces broken, cracked, or missing drawer rollers. Includes installation hardware for secure mounting.

Rear support wheel for dishwasher lower rack assembly. Replaces broken, cracked, or missing wheels that cause dragging or misalignment on the track.

Wheel and bearing assembly for dishwasher upper rack. Mounts to dishrack for smooth gliding on rails. Replace if worn, cracked, or broken wheels.

Replace cracked, broken, or missing upper rack wheels that cause the top rack to slide poorly or fall off the rail. Includes roller and axle assembly.

Threaded metal shaft that mounts the idler roller in dryers and washer-dryer combos. Replace if bent, worn, or stripped threads prevent secure roller installation.

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions

This float stem is part of the dishwasher's water-level/overfill system. It guides the tub float and actuates the float switch so the unit fills correctly and shuts off on time. Replace a worn or broken stem to restore reliable fill protection.

• Connects the float to the switch mechanism beneath the tub
• Provides smooth vertical travel of the float through the opening
• Triggers the float switch to stop filling at the proper level
• Causes symptoms such as no fill, continuous filling/overfilling, a stuck or wobbly float, or intermittent fill issues

• Disconnect power at the breaker and shut off the water supply before servicing
• Remove the lower rack; lift off the float cap from inside the tub
• On some models, release the retainer/clip from beneath the tub; pull out the old stem
• Guide the new stem through the opening and ensure it engages the float switch lever; confirm the float moves freely and actuates the switch before restoring power

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

Replacement wheel for dishwasher lower rack. Attaches to the dishrack to allow smooth gliding during loading. Needed when wheels are cracked or worn.

Secures the rack roller to the dishwasher tub wall for smooth gliding. Replace a cracked, broken, or loose mount to restore stable rack operation.

This is a single drum support roller that helps the dryer drum rotate smoothly during operation. The roller sits on a shaft at the rear or front of the drum and bears the weight of the drum as it spins. Replace this roller if the dryer makes a loud thumping, squealing, or rumbling noise during operation, or if the drum does not turn freely.

Upper rack wheel and mount assembly for dishwashers. Mounts to the upper dishrack to allow smooth rolling. Replace if cracked, broken, or worn.

Replacement pulley that guides the drive belt in your dryer. Needed when the original pulley is worn, seized, cracked, or causing belt damage.

This is a roller assembly that attaches to the lower dishrack of a dishwasher, allowing the rack to slide in and out smoothly. The roller includes the wheel and its mounting bracket. Replace this part if the lower rack is difficult to pull out or push in, rolls unevenly, or if the existing roller is cracked, worn, or missing.

Supports and centers the dishwasher spray arm for smooth rotation. Replace if worn, cracked, or causing wobbling. Installs under spray arm hub.

Supports the dryer drum and allows smooth rotation. Replace if cracked, worn flat, or causing the drum to wobble. Installs on the axle at rear or front.