Clip Or Clamp

Secure dryer hose clamp prevents air leaks and improves venting efficiency. Replace if loose, damaged, or during hose maintenance. Confirm fit with model.

This small terminal pin connects a wire to an appliance's electrical terminal, restoring a secure electrical connection so components receive reliable power and operation. Ideal for repairing loose or damaged wire terminations. What it does:

• Provides a secure metal contact point for a wire at a terminal or connector
• Restores proper electrical continuity when a terminal end is worn, bent, or broken
• Helps eliminate intermittent power, arcing, or component failures caused by poor connections
• Used wherever a single-pin wire termination is required on the appliance harness

• Disconnect power before servicing to avoid shock or injury
• Remove the damaged terminal and ensure the replacement pin matches shape and size
• Crimp or seat the pin per OEM guidance; ensure a snug, corrosion-free connection
• If wiring or harness insulation is damaged, replace the harness

Secures and organizes wiring harnesses inside your dryer. Replace if wires are loose, vibrating, or damaged. Confirm fit with your model number.

A small metal C-shaped retaining clip that secures shafts, pins or components in place to prevent unwanted movement. Simple, durable hardware that restores proper fit and alignment for the part it secures. What it does:

• Holds shafts, pins or rods in position to prevent axial movement or disengagement
• Restores secure attachment where a worn or missing clip allows parts to shift or fall out
• Used in moving assemblies to maintain alignment and proper function
• Fits in a groove or slot and provides spring tension for a tight hold

• One C-clip (retaining clip)

• Inspect the mating groove/pin for burrs or damage before installing the clip
• Use appropriate snap-ring or pliers to compress/expand the clip as needed; wear eye protection
• Ensure the clip fully seats in its groove and that the retained component moves as intended

This is a metal flange bracket that secures the heater housing assembly inside the dryer. It holds the heater box in the proper position to ensure safe and efficient heat distribution during drying cycles. Replace this bracket if it is bent, corroded, or broken, which can cause the heater housing to shift and lead to overheating or unusual noises.

A small metal retaining clip that secures a bi-metal thermostat or temperature sensor in place, helping maintain proper contact and accurate temperature sensing for reliable appliance operation. Simple, durable replacement part. What it does

• Holds a bi-metal thermostat or temperature sensor firmly against its mounting point or probe.
• Maintains consistent contact to support accurate temperature sensing and control.
• Can help stop intermittent temperature-related issues caused by a loose or damaged clip.
• Designed for direct replacement where a spring-style or formed metal retainer is required.

• One bi-metal retaining clip (single clip).

• Disconnect power to the appliance before attempting any repair.
• Removal/installation typically requires small pliers or a flat screwdriver; avoid excessive force to prevent damage.
• Verify clip orientation and that the sensor/thermostat is seated fully before securing.

This kit includes side mount clips and screws used to secure a garbage disposal unit to the sink or countertop. The clips provide a stable mounting point so the disposal does not shift during operation. Replace this kit if the clips are broken, missing, or corroded, which can cause the disposal to vibrate excessively or become loose.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Secures the control console to the cabinet, preventing rattles and loose movement. Replace when the panel sags or won't stay in place. Confirm fit.