Dishwasher Control Board

The Cntrl-Elec is an OEM component specifically designed for Whirlpool dishwashers. This control board governs and directs the electronic operations of the dishwasher. It allows the dishwasher to run through wash cycles and heat water to the appropriate temperatures. 

Symptoms of a bad control board include:

• The dishwasher not turning on at all
• The dishwasher not completing full cycles
• Issues with heating or not heating water properly
• Error codes appear continuously 

The control board is susceptible to faults over several years of regular usage. Water exposure or power surges can potentially damage electronic components. Replace yours with this genuine Whirlpool OEM part to restore full functionality to your dishwasher.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This electronic control board coordinates key refrigerator operations for consistent, reliable cooling performance. When the original board fails, replacing it restores the control logic that manages temperature regulation and other critical functions. What it does

• Regulates cooling cycles and defrost timing
• Controls and monitors the compressor and fan motors
• Processes sensor feedback and user control inputs
• Address symptoms such as not cooling, warm temperatures, unresponsive controls, or random cycling

• One electronic control board

• Disconnect power to the refrigerator before servicing; observe ESD precautions and handle the board by the edges
• Access the control compartment; photograph wiring and transfer connectors one at a time
• Verify all connections are fully seated and mounting points are secured
• Some models may require a control reset or initialization—follow the unit's tech sheet or service instructions

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, the control board orchestrates each cycle by coordinating motor, pump, heater and other component functions. It monitors cycle progression, temperatures and safety features.

Causes can be circuitry damage from power surges, water damage or normal component wear over time. Control boards experience constant usage with each cycle.

Symptoms of a bad control board include:

• The dishwasher not starting or powering on properly
• Inoperable or unresponsive buttons/controls
• Inability to advance through wash cycles
• Error codes displayed
• Cycle functions become intermittent

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Board is an OEM component specifically designed for Frigidaire dishwashers. It houses electronic components that direct machine operation through programmed cycles.

Causes of a faulty control board typically include failure of integrated circuits or microchips over time handling electrical signals. Damage from power surges is also possible. 

Symptoms of a bad control board include:

• No response to selector buttons  
• Inability to start or complete wash cycles
• Fault codes or blinking lights indicating errors  
• Intermittent or unusual mechanical behaviors

This OEM part fits Electrolux, Gibson and Kenmore models as well.

Restore reliable operation with this Electronic Control Board. It serves as the appliance's brain, interpreting user inputs and sensor feedback to coordinate functions and power the proper components when the original board has failed or become intermittent. What it does

• Processes keypad/touch inputs and executes programmed appliance logic
• Directs power or control signals to components as required for operation
• Monitors sensors/feedback to manage performance and safety routines
• Failure symptoms can include a blank/unlit display, unresponsive controls, won't start/complete a cycle, or recurring error codes

• 1 electronic control board

• Disconnect power at the breaker or unplug before servicing; verify no power is present
• Use anti-static precautions; handle the board by the edges and avoid flexing it
• Label or photograph wiring, then transfer connectors one at a time to the new board
• Ensure all harnesses are fully seated and the board is secured before restoring power and testing

This electronic control board governs the dishwasher's cycles and overall operation. Replacing a failed board can restore proper cycle selection, start-up, and progress so the appliance runs reliably again. What it does

• Orchestrates cycle timing and switching of internal components
• Processes inputs from sensors and the door switch to manage operations
• Communicates with the user interface/console and status indicators
• Failure symptoms include: won't start, unresponsive controls, cycles that pause or won't advance, random beeping, or error codes

• One electronic control board

• Disconnect power at the breaker before servicing; verify no power is present
• Use ESD precautions; handle the board by the edges only
• Photograph/label connectors and transfer them one at a time to the new board without forcing pins
• Inspect wiring and the door switch/harness for damage before reassembly and testing

The Control Board is an OEM component for Whirlpool dishwashers. As the central "brain" located under the dishwasher tub, this printed circuit board orchestrates all wash cycle functions and settings. 

Symptoms of a bad control board include:

• Failure to turn on or select desired cycles  
• Glitches in display readouts 
• Inability to advance cycles or unwanted resets
• Circuit board humming or buzzing noises

Causes of a bad control board can include water intrusion or prolonged exposure to steam damaging sensitive electronic components over time.

Replace with this Whirlpool board to restore reliable programming and dependable dish cleaning. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This electronic control board is the appliance's central controller. It interprets user inputs and sensor feedback to run cycles and coordinate components. Replacing a failed board can restore proper operation and responsive controls. What it does:

• Manages the timing and sequence of operations based on selected settings
• Interprets signals from the user interface and internal sensors
• Directs power to components via onboard electronics
• Monitors system status and may store/output diagnostic error codes
• Common failure symptoms: won't start, unresponsive or blank display, stuck/erratic cycles, or recurring error codes after a power reset

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the PCB by edges only
• Photograph/label connectors and move them one at a time to the new board to prevent miswiring
• Inspect wiring, fuses, and related components for shorts or damage and correct any root cause before powering the new board; follow the unit's tech sheet for any required post-install setup

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

The Electronic Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, this board regulates all wash and rinse cycles according to preprogrammed instructions. It communicates timing and commands to other crucial components.

Symptoms of a faulty control board include: 

• Failure to power on or unresponsive touch controls  
• Inability to select or advance through wash cycles
• Noise or vibration issues from improper component operation 
• Error codes appearing repeatedly on the digital display

Causes can involve water intrusion corroding circuits or individual component failure due to prolonged operation. Over time, environmental factors may inhibit board performance.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Control Board is an OEM part for Bosch dishwashers. It is the central electronic component responsible for operating and controlling all dishwasher functions. The control board receives input signals, processes commands, and directs the operation of wash cycles, motors, heating elements, and other electrical systems. 

Symptoms of a bad control board can include:

• The dishwasher is not starting or finishing cycles properly
• Lights, displays, or touchpads not working correctly 
• Strange noises coming from the dishwasher interior
• Inability to change programs or select desired cycle settings

Causes of control board failure may be due to electrical issues such as power surges, shorts, or general circuit malfunctions that can interfere with board operation over time. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The User Interface is an OEM part for Frigidaire dishwashers. As the user interface, it allows users to select cycles, options, and monitor dishwasher status.

Causes may be due to wear and tear over time, water damage, or shock/impact. This OEM Frigidaire part replaces the entire control panel assembly to restore full functionality.

Symptoms of a bad user interface include:

• Unresponsive or nonfunctional buttons
• Blank or dead display screen
• Inability to select cycles or options
• Erratic operation and unexpected behavior

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electronic control board is the appliance's command center. It reads inputs from switches and sensors, then directs power to components to run selected cycles—helping restore reliable operation when the original board fails.

• Coordinates timing and power to key components
• Interprets user commands and sensor feedback
• Manages cycle logic and stores/communicates fault codes
• Failure symptoms include no power, unresponsive controls, cycles that won't start or complete, or intermittent operation/error codes

• Disconnect power at the breaker before servicing
• Use ESD precautions; handle the board by the edges and avoid touching circuitry
• Note/photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, valves, fans) for shorts before powering up the new board

The USER INTERFACE PANEL is an OEM part for Whirlpool brand dishwasher models. It houses the electronic controls and digital display used to program cleaning cycles and adjust settings. 

Symptoms of a bad user interface panel include:

• Glitchy or unresponsive buttons that do not register selections
• Inaccurate or non-functional digital readouts  
• Failure to advance through cycles or changing programming 

As an interface device used frequently, the panel faces wear through repetitive touch inputs. Exposure to moisture splash-back or impact damage poses other risks to components over time. Replacing it with this genuine Whirlpool part restores reliable controls.

This OEM Whirlpool replacement user interface panel is also compatible with KitchenAid, Jenn-Air, Amana, Admiral, and some Kenmore dishwasher models. Secure operation maximizes convenience cycle after cycle.
 

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

This electronic control board is the dishwasher's main circuit board. It directs wash, drain, and dry functions and coordinates the user interface. Replacing a failed board restores responsive controls and reliable, complete cycles.

• Times and sequences wash, drain, and dry operations
• Distributes power to the circulation pump, drain pump, inlet valve, and heating circuit
• Monitors sensors and door switch; communicates with the display/indicator lights
• Common symptoms: won't start, unresponsive controls, cycles that stall or never advance, blinking lights or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD protection and handle the board by its edges
• Label/photograph connectors; transfer any mounting brackets or jumpers from the original board
• Some models require configuration/programming after install—follow the tech sheet stored inside the unit