Dishwasher Control Board

This speed control regulates and stabilizes motor speed in your appliance. Replacing a faulty control restores smooth start-up and accurate speed selection so the motor runs consistently at the setting you choose.

• Modulates power to the motor to reach and hold the selected speed
• Helps correct issues like surging, stalling, or running only at one speed
• Common symptoms include erratic speeds, failure to start, or sudden speed changes
• Also presents as an unresponsive speed selector or inconsistent performance

• Disconnect power before servicing and allow components to discharge
• Access the control per your model's service information; note wire locations or take photos
• Transfer connectors one at a time; seat fully and handle electronics with ESD care
• Reassemble and test operation through all speed settings; perform any model-specific calibration if required

This electronic control board is the appliance's brain, directing power and timing to key components. Replacing a failed board can resolve unresponsive controls, erratic operation, or recurring error codes for reliable, consistent performance.

• Manages cycle logic and timing based on user selections and sensor inputs
• Distributes power to motors, heaters, valves, and other components as programmed
• Interfaces with the display and buttons to execute commands
• Flags faults and stores error codes when issues are detected
• Common signs of failure: won't start, blank or flickering display, erratic cycling, or repeated error codes

• Disconnect power before servicing; verify no voltage is present at the board
• Use ESD precautions—handle by the edges and avoid touching circuitry
• Transfer any brackets/covers and move wire connectors one at a time to maintain placement
• Some models require a post-install diagnostic or configuration step—follow the tech sheet for your unit

This electronic control board is the appliance's central controller, managing critical functions and timing. Replacing a failed board restores proper operation, responsive controls, and consistent performance when the unit is unresponsive, shows errors, or behaves unpredictably.

• Processes user commands and internal signals to run cycles as designed
• Controls or communicates with motors, valves, fans, and heaters through onboard components
• Manages timing, temperatures, and safety checks programmed by the manufacturer
• Symptoms of failure: won't power on or start, dead or erratic controls, error codes, intermittent operation

• Disconnect power to the appliance before servicing; also shut off gas/water
• Use anti-static precautions and handle the board by its edges
• Photograph connections; transfer connectors one at a time to the new board; secure in the original mounting
• After installation, follow your model's tech sheet for any required initialization/diagnostics and verify normal operation

This dishwasher timer controls the sequence and duration of each cycle step. Replacing a worn timer restores proper cycle advancement so the unit fills, washes, drains, and dries at the right time.

• Sequences the dishwasher through fill, wash, rinse, drain, and dry stages
• Advances the cycle at the correct intervals to complete each step
• Failure may cause cycles not to start, not to advance, or to stop mid-cycle
• Common symptoms include getting stuck in a cycle, running too long, or the control knob not advancing

• Disconnect power at the breaker before servicing
• Access the timer behind the control console; remove inner door/console screws as needed
• Photograph/label wiring and transfer wires to the new timer one at a time
• Mount securely, reassemble the console, restore power, and test a full cycle

Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. If you require the Jumper Wire that goes with certain models, the part number is 00167782.

This part is a tactile control assembly kit that is used on a dishwasher. The tactile control assembly is the system that uses touch to make adjustments. For example, the buttons are connected to this tactile control assembly, and when the buttons are pressed, it is activated. A new tactile control assembly kit may be needed if the dishwasher keypad is entirely unresponsive when the buttons are pressed. If this is the case, the dishwasher will not be able to be used at all. The replacement process is relatively easy and takes anywhere from 30 to 60 minutes to complete. A screwdriver will be needed for the replacement.This tactile control assembly is a genuine General Electric part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific tactile control assembly is compatible with dishwashers that are manufactured by the General Electric brand.

The electronic control board is the appliance's main control module. It interprets inputs from the user interface and sensors, then powers and times key components to run each cycle. Replacing a failed board restores reliable, predictable operation.

• Coordinates cycle sequencing and powers components through onboard relays
• Receives signals from switches/sensors and manages overall operation
• Common failure symptoms: unresponsive controls or no power
• Won't start, stops mid-cycle, or won't advance through a cycle
• Intermittent operation, flashing lights, or fault/error codes tied to the main control

• Disconnect power at the breaker before servicing; verify the unit is de-energized
• Use ESD protection; handle the board by the edges to avoid static damage
• Photograph/label wiring and move connectors one at a time to the matching terminals
• After installation, run the appliance's diagnostic/test cycle to confirm proper operation

The Electronic Control is an OEM part for Whirlpool dishwashers. It is the main circuit board that regulates all electrical functions and directs components during cycles. Sensors throughout the dishwasher relay information to the control board, which processes data and generates output signals to control mechanisms such as wash motor, heater and dispensers.

Causes of a bad electronic control include failures from long-term, continuous usage overload, issues due to power fluctuations or surges that disrupt circuitry.

Symptoms of a bad electronic control include: 

• Fault codes displayed 
• Lights, buttons or other functions malfunctioning
• Inability to start cycles or advance through phases
• Irregular cycle times, temps or abnormal sounds  

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore models. 

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions

The Dishwasher Electronic Control Board is essential for managing the various functions of your dishwasher efficiently. This genuine OEM part ensures reliable performance and seamless integration with your Samsung dishwasher. Designed to handle multiple cycles and settings, it helps maintain optimal cleaning results every time. The Electronic Control Board features durable components that contribute to the longevity of your appliance, reducing the need for frequent repairs. Its precise engineering allows for easy installation, making it a convenient solution for restoring your dishwasherGÇÖs functionality. Compatible with a range of Samsung dishwasher models, this genuine OEM part guarantees a perfect fit and dependable operation. By choosing the Dishwasher Electronic Control Board , you enhance your applianceGÇÖs reliability and ensure it continues to perform at its best, providing you with the quality and efficiency you expect from Samsung.

This dishwasher timer controls the timing and sequence of wash, rinse, drain, and dry operations. Replacing a failed timer ensures the machine advances through each stage properly for complete cycles and reliable cleaning results.

• Advances the cycle and routes power to pumps, valves, and heater at the correct times
• Can cause cycles to run unusually long/short or skip steps when failing
• Intermittent start/stop behavior during a cycle can also indicate a worn timer

• Disconnect power at the breaker before servicing
• Access the control console; document wire locations and transfer one lead at a time to the new timer
• Mount securely and route wires clear of sharp edges or moving parts
• Restore power and run a short test cycle to proper advancement

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

This switch assembly is used in select dishwashers to provide a precise open/closed electrical signal to the control. Replacing a worn or sticking switch helps restore consistent cycle operation and reliable responses from the affected function. What it does:

• Sends an on/off (open/closed) signal to the control for the related mechanism in your model
• Helps ensure the connected function engages only at the correct time
• Common symptoms of a failed switch can include: cycle won't start, intermittent stopping, or improper filling/draining behavior
• A sticking or heat-damaged switch may cause erratic operation or error alerts

• One switch assembly

• Disconnect power (and water supply if required by access) before servicing
• Access location is model-specific; photograph wiring and note terminal positions before removal
• Transfer or reuse existing mounting hardware as applicable; ensure firm terminal connections
• After install, check switch actuation and run a test cycle to normal operation

This electronic control board is the appliance's central command module, directing power and timing so functions run correctly. Replacing a failed board helps restore normal operation when the unit is unresponsive or behaves erratically.

• Manages power and timing to components based on selected settings
• Interprets inputs from sensors/switches to control each step of the cycle
• Common symptoms: won't power on or start, unresponsive controls, random stopping, error codes/alarms

• Disconnect power before service; use ESD protection and handle the board by its edges
• Photograph wire/harness connections and transfer connectors one at a time
• Inspect and correct any shorted components or damaged wiring before powering up the new board
• After installation, follow the unit's tech sheet for any required tests, calibration, or programming steps

This user interface is the electronics behind a full-door console dishwasher panel. It reads your button selections and communicates with the main control so cycles start and options respond reliably.

• Interprets keypad inputs from the console and sends commands to the control board
• Helps restore proper control of wash cycles, options, and start/delay functions
• Common symptoms: unresponsive or intermittent buttons, no console lights, can't start from the panel, erratic beeping/stuck-key behavior
• Built for full-door (full-console) configurations used on select models

• Disconnect power at the breaker; turn off the water supply
• Remove inner door/console screws to access the UI; support the panel to avoid straining wires
• Handle the board with ESD care; transfer any mounting clips/brackets and seat ribbon cables/connectors fully and correctly
• Reassemble the door and test console operation before running a full cycle

The is is a dishwasher control board. This part is tasked with controlling all of the internal parts of the dishwasher. It regulates the wash cycle, drying cycle, and other parts of a typical washing cycle. This part has many internal components and can become damaged over time or through use. If the dishwasher does not run, starts a cycle but doesn't finish it, or otherwise has functioning issues, this could mean the control board should be replaced.Before starting, make sure the dishwasher is unplugged for safety reasons. Open the door and remove the screws from the inner panel. Separate the panels while disconnecting the wire harness from the control panel. Pull the outer door panel and control panel off the appliance. Install the new part and reconnect wires and ribbons before reassembling the dishwasher. Plug in the appliance and test it.This is a genuine OEM replacement part designed to be compatible with dishwashers by Kenmore and Whirlpool. The control board comes directly from the manufacturer and is sold as a single component.