Dishwasher Control Board

This main electronic control board governs the appliance's user interface and cycle functions, restoring responsive controls and correct operation when the original board fails. Replace a faulty control board to correct erratic or unresponsive behavior. What it does:

• Receives input from the console and sends control signals to relays, valves, motors and sensors.
• Restores normal cycle selection and timing when a failed board prevents the appliance from starting or completing cycles.
• Addresses symptoms like unresponsive or non-working buttons, blank or erratic displays, and unexpected program changes.
• Interfaces with safety and feedback sensors to coordinate appliance functions.

• Always disconnect power to the appliance before replacing the control board to avoid shock or damage.
• Handle the board by its edges and avoid touching circuit traces or components; the board is static-sensitive.
• Note connector locations or photograph wiring before removal to ensure correct reassembly.

This electronic control board is the appliance's main control (PCB) that coordinates programmed functions and powers key components. Replacing a failed board restores accurate cycle timing and responsive controls for reliable, consistent operation. What it does

• Manages the timing and sequencing of appliance operations
• Interprets inputs from the user interface, sensors, and switches
• Controls power to loads such as motors, valves, heaters, and fans
• Common symptoms of failure: won't start or complete a cycle, unresponsive or erratic controls/display, error codes/alarms, or intermittent operation

• 1 electronic control board

• Disconnect power (unplug or switch off the circuit breaker) before servicing
• Use ESD protection and handle the board by its edges to avoid static damage
• Note/photograph wire locations; transfer connectors one at a time and seat them fully
• Run diagnostics/self-test after installation if available

This is a Bosch dishwasher control board. The dishwasher's control board ensures that the various cycles and settings can be properly managed, such as the washing and draining cycles. If the user notices issues with dishes not coming out clean after a full cycle, the control board should be checked for error codes or signs of visible wear and tear that may indicate it needs to be replaced. Make sure that the dishwasher is turned off, unplugged, and completely disconnected from its power and water sources. It's recommended that work gloves are worn to prevent injury. This is a genuine OEM part and has been sourced directly from the manufacturer. This is an authentic part and as such is sold individually and made from durable, high-quality, non-corrosive materials to ensure the highest possible quality. This part is compatible with dishwashers that have been manufactured by Bosch, Thermador, Gaggenau, and various other brands.

This electronic control module replaces the oven/range control board that manages user inputs, timers/clock and heating cycles so the appliance responds correctly and restores control functions. What it does:

• Receives inputs from the front console and controls bake, broil, timers and display functions
• Regulates oven cycles and relays commands to power components (elements, ignitors, fans)
• Common symptoms of failure: unresponsive touchpad/controls, blank or erratic display, oven not heating or not following selected cycles
• Replacing a faulty module often resolves intermittent operation and control-related error codes

• Disconnect power to the appliance before starting any service to avoid shock or injury
• Access typically requires removing the console or control panel; handle the board and connectors carefully
• Avoid touching circuitry or terminals; ground yourself to reduce static risk
• Follow the appliance service manual and wiring diagrams

The Timer is an OEM part for GE dishwashers. It regulates the various cycles of the dishwasher, such as washing, rinsing, and drying, ensuring each phase occurs for the appropriate amount of time.

Causes of a bad timer can include electrical failures, wear and tear over time, or mechanical issues that disrupt the timer's ability to accurately control the dishwasher's cycles. A malfunctioning timer can result in incomplete washing or rinsing, affecting the dishwasher's overall performance.

Symptoms of a bad timer include:

• Dishwasher cycles running too long or too short
• Dishwasher not advancing to the next cycle
• Dishwasher stopping mid-cycle
• Inconsistent cleaning results

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This electronic control board is the appliance's central controller, interpreting user inputs and managing power to key components. Replacing a failed board restores responsive controls, proper cycle execution, and reliable overall operation. What it does:

• Interprets keypad or selector inputs and executes programmed functions
• Switches relays to power motors, valves, heaters, and other loads as required
• Drives the display and status indicators; stores and shows diagnostic/error codes
• Monitors sensor inputs to protect the appliance and maintain correct operation
• Common failure symptoms include a blank or unresponsive display, inability to start cycles, erratic operation, or error codes traced to the control

• 1 electronic control board

• Disconnect power to the appliance before servicing; follow all safety precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to match original locations
• Some models require a service/diagnostic or configuration step after installation; refer to the unit's tech sheet or service guide

Replacement main control board and tactile board kit restores control and user input when the original electronics or buttons become unresponsive, helping return oven/range controls and display responsiveness. What it does:

• Primary control board: manages the appliance's electronic control functions and communicates with the user interface.
• Tactile board: provides the button interface so touch or press inputs register with the control module.
• Common symptoms addressed: unresponsive or intermittent buttons, unresponsive or blank display, or controls that do not respond reliably.
• Replaces both the main module and its associated keypad in one kit for a matched repair.

• Disconnect power at the breaker before starting any repair to avoid shock or injury.
• Handle circuit boards by the edges and avoid static discharge; use an ESD strap if available.
• Replacement typically requires removing the control panel and unplugging/reconnecting wiring harnesses; keep track of connector locations.

The Control Board is an OEM replacement part for Frigidaire dishwashers. Located inside the cabinet behind the control panel, the control board utilizes integrated circuits and electronic components to regulate all dishwasher functions. It receives input signals from the control buttons to initiate and monitor the wash cycle. 

Causes of a bad control board can include failures of electronic components over time, voltage fluctuations that cause circuit damage, or moisture infiltration leading to corrosion.

Symptoms of a bad Control Board include:

• Dishwasher fails to start or stops mid-cycle unexpectedly
• Lights or displays on control panel malfunction  
• Inability to select options or cycles
• Complete non-responsiveness of control functions

This board is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore dishwasher models.

This kit replaces both of the dishwasher's primary electronic controls: the main control board and the tactile board. Replacing them together can restore reliable cycle selection and overall operation when control failures occur. What it does

• Main control board directs cycle logic and powers pumps, valves, heater, and sensors
• Tactile board registers button presses and communicates selections to the main control
• Can address erratic lights/tones or cycles that won't advance due to control faults

• 1 main electronic control board and 1 tactile board

• Disconnect power at the breaker before servicing
• Use ESD protection and handle boards by the edges
• Photograph wiring; transfer one connector at a time to the new board
• Fully seat all ribbon/plug connectors; match any jumper/DIP settings to the original if present

Restore your dishwasher's brains with this control assembly. It manages cycle selection and timing so the machine responds to commands, starts reliably, and completes wash cycles without random beeps, stalls, or unresponsive controls.

• Coordinates cycle logic and component operation
• Interprets button/touch inputs from the console
• Drives status indicators or display on applicable models
• Typical symptoms: controls unresponsive, won't start, lights flicker or beep erratically, cycle won't advance

• Disconnect power at the breaker before servicing
• Use anti-static precautions; handle the board by its edges and avoid touching contacts
• Label/photograph wiring; move connectors one at a time and fully seat any ribbon cables/locks
• Reuse existing mounting hardware; ensure correct orientation and secure harness routing before reassembly

Replacement control unit that manages the appliance's electronic functions, handling cycle timing, user inputs, and control signals to restore normal operation. Fits where the original electronic control board controls cycles and the user interface. What it does:

• Serves as the appliance's primary electronic control board, processing button/keypad commands and sequencing cycles.
• Controls cycle timing, relays, and signals to motors, valves, and heaters.
• Common symptoms of a failing unit: unresponsive controls, cycles won't start or advance, or intermittent operation.
• Does not include peripheral components such as face panels, knobs, or separate display overlays.

• Always disconnect power to the appliance before starting work to avoid shock or damage.
• Handle the board by its edges and avoid touching circuits; wear an anti-static wrist strap if available.
• Verify connector orientation and seat all wiring harnesses firmly; check harness routing before reassembly.

Electromechanical timer that controls a dryer's cycle selection and timing, restoring correct cycle progression and automatic shutoff. Ideal when cycles won't advance or the dryer runs irregularly. What it does:

• Advances the dryer through selected cycles and signals timed shutoff.
• Replaces a faulty timer that prevents cycle selection or stops cycles from advancing.
• Can resolve symptoms like dryer not advancing through cycles, running continuously, or failing to start selected cycles.
• Works with the dryer's control circuitry to coordinate timed and automatic functions.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Remove the control panel to access the timer; keep track of mounting screws and wire locations.
• Transfer wires exactly as removed; take a photo before disconnection to aid reassembly.

The Timer regulates the sequence and duration of dishwasher cycles. It advances power to each component in order so the machine washes, drains, and dries at the correct times for dependable operation.

• Controls and advances the dishwasher through each programmed step
• Routes power to the fill valve, wash motor, drain pump, and heater in sequence
• Failure can cause the cycle not to start or advance, to stop mid-cycle, or to run too long
• Intermittent contacts may lead to skipped steps or inconsistent drying/heating

• Disconnect power at the breaker before servicing
• Access the control/console area; remove the knob and mounting hardware as needed
• Label or photograph wire positions; transfer wires to the new timer one at a time
• Mount securely, reassemble panels, restore power, and run a test cycle

Color: Black

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, it directs all functions of the dishwasher from start to finish.

The board regulates tasks like detergent dispensing, and activating the wash and rinse arms. It carries out programmed cycles chosen by the user seamlessly and cleans each load of dishes.

Causes of a bad control board can include defects resulting from continued exposure to high heat and moisture during cycles as well as accidental impact or power surges over time.

Symptoms of a bad control board include:

• Failure to initiate selected cycles or advance to different phases
• Lights not illuminating or buttons malfunctioning
• Abnormal noises coming from the interior
• Dishes not getting fully clean after a cycle

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The control module assembly is the dishwasher's electronic brain. It manages cycle timing and powers key loads so the unit starts, runs, and completes wash and dry functions reliably when the original board fails. What it does

• Controls cycle timing and distributes power to the wash motor, drain pump, heater, and water inlet valve
• Interfaces with the door latch and user keypad to start/stop cycles
• Monitors inputs to manage heating and drying functions
• Replacement may help if the dishwasher is dead/no lights, won't start, stops mid-cycle, or runs erratically
• May also address intermittent beeping or error indications traced to a failed control

• 1 control module assembly

• Disconnect power at the breaker before servicing; verify no voltage is present
• This is an ESD-sensitive board—use anti-static precautions and handle by the edges
• Access location varies by model; label/photograph wiring and move connectors one at a time
• After installation, ensure all connectors are fully seated and run a test cycle to confirm operation

This electronic control board is the appliance's main control. It directs power and timing to the correct components so cycles run as selected, helping restore consistent operation when the original board has failed.

• Coordinates operation of motors, valves, heaters, and pumps
• Interprets inputs from switches and sensors to manage cycle logic
• Stores and executes programmed options and settings
• Typical symptoms: won't start or advance, unresponsive or flashing controls, error codes, intermittent shutdowns

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Access is typically through the control console; refer to your model's service sheet for exact location
• Move wire connectors one at a time to the new board and secure it properly
• Perform any required initialization/diagnostic steps for your model after installation