Dishwasher Pump

Dishwasher failed to run normal cycle. Would fill and then empty, but would not run through the normal rinse/clean cycle. Determined that the Sump/Motor Assembly needed to be replaced. Dishwasher had to be pulled out to access part. Was difficult to snap into place and had to maneuver several times to get a tight seal before reattaching peripheral components. Ran a one-hour cycle to test for leaks and efficiency before reinstalling unit under counter. Read more

I've had to repair this appliance before, and it's almost always the motor-pump that needs replacing. It's a pretty easy fix if you have a roll out dishwasher. All you have to do is flip the dishwasher on its back, unhook the pump (no tools required, just push down the locking tab and twist and disconnect the wiring), and plug in the new one. I noticed that the tub wasn't draining completely either, so I replaced the drain pump as well just to be on the safe side. If, as I did, you let this... Read more

Replaced the spray arm along with several other maintenance items (filters, pump housing, etc) on my Kitchenaid dishwasher. Repair went well and best of all the parts were shipped to me in just 1 day which was incredible. Read more

I had a repairman in to check why machine had no power. I watched as he opened the door up and secured the electrical ribbon in place and lights on control panel came on. Asked him questions about the noise he confirmed it was the blower. would have charged me around $250.00 to replace that. Spoke to a rep on the phone and ordered the part for $100.00. The replacement part arrived in 1 day. Looked at the parts diagram on your site to orient myself. Separated the the front door( screws)... Read more

In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside. Read more

Replaced the pump drain assembly Read more

• Noisy

Diagnosed the problem. The pump motor needed to be replaced. Took model number and looked part up on Appliance Parts Pro site and found the exact part. Ordered part with next day delivery . Part arrived as scheduled. Simple installation. Works like new. Thanks. Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more

I followed the video instructions that is on the website and was able to replace the motor easily and in 15 minutes maybe less. Read more

I began the repair process with basic troubleshooting. The two-year-old Whirlpool dishwasher was not washing. At first, I thought it was not getting water. I did a system drain which removed most of the water. I waited a few minutes then attempted a light wash cycle without success, but I did hear the unit getting water. And I noticed the detergent cube slightly moistened on the floor of the washer. Google led me to your YouTube videos. I assumed (and hoped) it was the pump. From what I read... Read more

Replaced the pump and drain hose. The pump was easy. The replacement parts were identical to the bad parts. The drain hose was full of gook and smelled awful so I decided to replace that as well. The tag on the new hose alerted me to the procedure for installing a drain hose. If your dishwasher is not vented you need to create a high hose loop so that excess particles from the garbage disposal or dishwasher don't stay in the hose. The person that installed the dishwasher failed to do this which... Read more

• Noisy
• Won't start

The PC board was bigger than the original so had to modify the mounts, the pump and rotor are pretty straight forward but would have much easier with another pair of hands. It took about 2 hours start to finish. One and a half days to get the parts, fantastic service. A new dishwasher is $1300.00. the parts were $314.00, so more than worth fixing. Read more

I paid $90 for a repairman fee to tell me I needed a motor. I submitted the same problem to you and you gave me the same advice for FREE. I ordered the unit from you . It came in promptly, It took me about 3 hours to replace and saved about a $300-$400.repair estimate. Thanks. Read more

Replace the leaking seal. Part fitment was original and easy to replace. Read more

• Noisy

Could not have went better. The girl in customer service verified all my parts prior to my ordering. I paid for next day shipping and they arrived on time. Exact replacement items for our Frigidaire dishwasher. Will give all of my future business to Appliance Parts Pros. One precaution...when manually entering my model number on the website, incorrect part numbers were displayed. Make sure you have their online chat representatives verify your parts and you will be good to go. Read more