Dishwasher Pump

Replaced sump because the seal is not sold separately. You will need a skinny clamp after cutting the original swaged clamp off. Also Had to replace the cover as its seal is not sold separately either. Used dish soap on seals during assembly. Read more

Replaced filter. It works great now, no more brown spots. Read more

So all of a sudden the dishwasher stops working, "0E error"on the panel. Did some google searches and found that it might be the filter, which I did not know needed to be changed, or worse, the motor. Took the filter off per online tutorial (easy) and mopped up all the stagnant water. Poking around, I find the small rubber check valve that has broken. Had to fish it out with tweezers. Long story short, it was not the motor and I doubt it was the filter. It was this $1.87 rubber drainage... Read more

Found model number on side of dishwasher. Went online to appliance parts pro. I was very easy to find the part I needed. Part arrived in 2 days. replaced part, took about 20 minutes, not complicated just loosened two clamps and put in new drain pump. Read more

The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more

Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more

I stood by the dishwasher as it went through the cycles and noted the noise only happened during the drain processes. To make this repair you have to take the dishwasher completely out from under the counter. (NOTE: print the schematic to help guide you to the location of the part and connections.) The pump is not accessible from underneath. I laid the dishwasher on its side. I recommend disconnecting the copper fill tubing before laying the machine over (I did not and crimped it). The... Read more

I ordered a new motor through ApplianceParts Pros.com and had the new part within 5 days. The entire replacement took approximately 1 1/2 - 2 hours. The repair was relatively simple and straight forward. By doing the work myself I saved over $250. Originally a GE technician quoted a price of $489 to replace the motor to repair the dishwasher. For that price I could have bought a new dishwasher (Electronix Express $491) but not with all the features of my current appliance. By doing the... Read more

• lights flashing or blinking

Since my Samsung Dishwasher would not drain and had a flashing quick light, I removed the racks and both spray wands. Which allowed me to remove the lower screen assembly. This revealed a worn and broken check valve and broken grinder blade. I cleaned the inside of the dishwasher and removed the unit from under the counter. I removed and cleaned the brake assembly ( large transparent plastic section on left side of the dishwasher). I cleaned this for preventive maintenance by taking the float... Read more

Replaced pump impeller. Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more

I started looking at new dishwashers and was quickly disheartened with the cost of these simple machines. There's really not much to them and yet they're so much money for what they do. I popped off the pump and took a look at it and cleared some "gunk" and hair out but it didn't fix the issue. Jumped on AppliandPartsPros.com and ordered the pump on a Friday night and had the part in hand Tuesday night after work. Took about 10 minutes total (dishwasher out and back installed, literally in... Read more

Ordered the pump & motor. Installed it myself ..Being a female, I feel pretty proud!! Read more

I had clogs before, so I knew this wasn't the case. When I tried the "rinse and hold" setting, the water would fill, but no sound when it tried to drain. I suspected the pump. Searching through YouTube, I found a helpful video for the GE Profile unit. In fact, the video directed me to this site for parts. It seemed simple enough to replace and I verified the part number to order. I pulled out the dishwasher, laid it on it's side, swapped the part, put it back in, and tested. It now works... Read more

Replaced pump, found impeller on pump failed. Unfortunately had to replace entire pump, could not just buy impeller. Read more