Fuse Or Sensor

Microwave won't turn on or has no power? This fuse and holder assembly restores overcurrent protection when a blown fuse interrupts operation.

Fix TE error code on your washer with this thermistor temperature sensor. Restores accurate temperature sensing and reliable cycle control.

Thermistor is a temperature-sensing replacement that monitors refrigerator and freezer temperatures so the control board can regulate cooling. Replacing a faulty thermistor restores accurate temperature readings and helps stabilize cooling performance. What it does:

• Senses interior/evaporator temperature and sends a signal to the control board for temperature regulation.
• Helps prevent erratic cooling, long run-times, or inconsistent compartment temperatures when operating correctly.
• Faulty thermistors can contribute to excessive frost, failed defrost cycles, or compressor cycling issues.
• Use when the existing sensor fails to report correct temperatures or the part number matches.

• Always disconnect power to the appliance before servicing to avoid shock or damage.
• The sensor is typically mounted on or near the evaporator or inside a cabinet wall; access may require removing panels or covers.
• Handle the sensor and wiring harness gently; avoid pulling on wires or bending the sensor element.

Warming drawer won't heat or power on? This thermal fuse cuts power when temperatures exceed safe limits. Straightforward replacement fix.

If your range meat probe gives inaccurate readings or doesn't work, this temperature sensor monitors internal cooking temps. Easy 15-minute DIY fix.

Fix an overheating oven with this range limit thermostat. Stops heating when temperatures exceed safe limits. Straightforward repair for most DIYers.

This SPDT high-amp switch controls high-current circuits by switching one input between two outputs, restoring proper electrical control in affected appliance functions. Built for high-load switching where reliable on/off selection is required. What it does:

• Directs high-current power from a single input to one of two outputs (single-pole, double-throw action)
• Replaces worn or failed selector/limit-style switches that cause intermittent or no power to a circuit
• Commonly used where a high-amp, durable switching contact is required to complete a function
• Helps stop symptoms like intermittent operation, failure to switch between states, or no power to the controlled circuit

• One SPDT high-amp switch (WB24T10160)

• Disconnect power to the appliance before inspecting or replacing the switch
• Verify wiring locations and take a photo before removal for correct reconnection
• Use proper tools and avoid touching energized contacts;

Dryer overheating or not heating properly? This cycling thermostat regulates drum temperature to prevent damage. Common DIY fix, 30 minutes.

Dryer not heating properly or overheating? This cycling thermostat regulates temperature by cycling the heating element on and off. Moderate DIY repair.

Dryer won't heat or overheats? This high limit thermostat cuts power when temperatures get too high. Common fix for no-heat issues. Easy install.

This 20-amp circuit breaker restores overcurrent protection to the appliance's electrical circuit, helping prevent damage from short circuits or overloads. It replaces a worn or tripped breaker so the appliance can receive proper power. What it does:

• Acts as an overcurrent safety device that trips when current exceeds safe limits
• Protects wiring and components from damage caused by overloads or short circuits
• Common symptom: appliance won't power on or stops powering intermittently
• Common symptom: breaker repeatedly trips during normal operation

• Disconnect power at the house breaker before inspecting or replacing the part
• Handle terminals carefully; ensure connectors are fully seated and tight
• Replace with the exact part number for fit and proper electrical rating

Cooktop burners not heating? A blown thermal fuse cuts power to prevent overheating. Test for continuity and replace to restore heating function.

Fix a dryer that won't heat with this thermostat. Regulates heating element temperature to prevent overheating. Moderate DIY repair in under an hour.

This protective fuse safeguards the appliance's electrical circuit. When an overcurrent or short occurs, it opens the circuit to cut power and help prevent damage. Replacing a blown fuse can restore power once the underlying issue is corrected.

• Opens the circuit when current exceeds its design limit or a short is detected
• Helps protect control and other internal components from electrical damage
• Typical symptoms of a failed fuse include no power, dead display/controls, won't start, or immediate power loss
• An underlying electrical fault is likely present and should be diagnosed

• Disconnect power at the breaker or unplug the appliance before servicing
• Replace only with the exact type and rating specified for your model; never bypass or upsize a fuse
• Inspect wiring and components for the root cause of the blown fuse before restoring power
• If servicing a microwave, follow the service manual and discharge the high-voltage capacitor; consider service due to shock risk

Dryer won't heat or stops when hot? A faulty cycling thermostat disrupts temperature regulation. Testing with a multimeter confirms the issue.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.