General Electric Burner & Related Parts

Color: Black. This large cap measures about 3-1/2 inches in diameter.

This gas valve regulates and safely delivers fuel to your dryer's burner. When operating correctly, it opens for ignition and closes when heat is satisfied, providing consistent, reliable heating for effective drying.

• Opens to allow gas into the burner when the ignition system calls for heat
• Closes to stop gas flow during cycling or if ignition fails
• Possible symptoms: dryer runs but no heat; igniter glows yet no flame; intermittent heat or long dry times
• Helps restore proper burner ignition and stable flame

• Disconnect power and shut off the gas supply before servicing
• Work in a well-ventilated area; check all connections for leaks with a non-corrosive leak-detection solution after installation
• Transfer any brackets, fittings, or orifices from the original valve as required; secure connections
• Confirm gas type (natural/LP) and regulator/orifice settings per the service manual before restoring service

Color: Black. Small

Lower oven bake assembly that supplies heat for the bake cycle. Replaces a damaged lower element to help restore proper oven baking performance and even oven temperatures. What it does:

• Heats during the bake cycle to generate oven baking temperature.
• Replaces a burned-through or damaged lower bake element.
• Commonly used when the oven won't heat on bake, heats unevenly, or the element is visibly broken.
• Works with the oven's original terminals and mounting points to restore bake function.

• Disconnect power at the breaker before starting any repairs; verify power is off.
• Allow the oven and element to cool completely and handle the element gently to avoid damage.
• Installation may require removing the oven floor or back panel to access the element; follow the oven service manual for step-by-step instructions.

Medium. Color: Grey. It measures about 3 inches in diameter.

Large. Color: Grey. It measures about 3-1/2 inches in diameter.

H Burner

This bracket secures the cooktop/main top to the appliance chassis to keep the surface stable and properly aligned. Replacing a bent or missing bracket can eliminate looseness, rattles, and visible gaps so the top seats correctly.

• Anchors the cooktop/main top to the frame
• Maintains proper spacing and alignment of the top
• Helps prevent vibration and movement during use and cleaning
• A damaged or missing bracket can cause a loose, uneven, or rattling cooktop

• Disconnect power and, for gas units, shut off the gas supply before servicing
• Access the bracket location per your model's service procedure (top may need to be lifted or removed)
• Transfer and reuse mounting screws/clips from the original bracket if required
• Install in the same orientation, check alignment, and tighten fasteners securely before restoring service

This is a burner head, and it is intended for use ranges or stove top ovens. This is a genuine replacement part made by General Electric. Burner heads are used on the top of stoves or ranges to provide heat.A new burner head might be needed if the current one is unable to turn on or off. Another way to determine if a new burner head is needed is if the knobs indicate the burner should be putting off heat but the burner head does not feel hot to the touch. Be sure the current burner head is fully connected before determining whether a new one is needed.This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with ranges or stoves made by General Electric.

Approx 3 inches in diameter

Small. Color: Grey. It measures close to 3 inches in diameter.

Approx 4 inches in diameter

This double burner assembly restores proper gas flow to a two-burner section of the cooktop so it lights reliably and heats evenly. Replace a worn or damaged assembly to correct ignition issues and irregular or weak flames.

• Routes gas to two burner outlets under the main top
• Provides the orifice-holder structure that mates to the burner head(s) and igniter(s)
• Aligns and supports burner heads for stable mounting
• Typical symptoms: one or both burners won't light, flames are weak or uneven, or the assembly shows cracks, corrosion, or stripped threads

• Turn off gas supply and disconnect power; allow the appliance to cool completely
• Remove grates, caps, and burner heads; raise or remove the main top to access the assembly
• Note tubing and component positions; install the new assembly and tighten all fittings securely
• After reassembly, check all gas joints with an approved leak-detection solution and verify proper ignition and flame

Color: Black

Black. D Burner

15K