General Electric Burner & Related Parts

Color: Black

Black. H Burner

Black. D Burner

15K

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Approx 2-1/2 inches in diameter

This surface burner cap is a genuine General Electric part, sold individually. It can be used as a replacement part for a gas range. This surface burner cap provides a covering for the burner of the gas range so that the infrastructure of the burner and the ignition are not damaged in the process of utilizing the burners.A surface burner cap might have to be replaced if it is lost, misplaced, or has suffered damage that prevents the component from protecting the burner and the ignition. Damage can include punctures, cracks, chips, or erosion to the material that weakens the ability of the component to protect the burner and ignition. If this damage occurs, the component should be removed and replaced by this genuine OEM replacement part. It is a simple replacement process that will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This surface burner cap is compatible with General Electric brand gas ranges.

This burner assembly is the combustion head for GE gas dryers. It mixes gas and air and directs a stable flame into the heater housing, restoring consistent heat when the original burner is corroded, warped, or clogged.

• Directs the gas flame into the heat chamber for proper drying temperatures
• Works with the igniter, flame sensor, and gas valve to produce heat
• Typical failure symptoms: no heat or intermittent heat, long dry times, burner lights then goes out, unstable/yellow flame
• Physical issues can include rust, warping, or blocked burner ports

• Disconnect power and shut off the gas supply; allow the dryer to cool completely
• Note position of the igniter and flame sensor relative to the burner port; realign during reassembly
• Transfer any reusable fittings from the original burner as needed and verify orifice/fuel type match your installation
• After reconnecting gas, perform a leak check with a non-corrosive soapy water solution before restoring power

18K Simmer

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

Black. C Burner

This head burner main is the primary gas burner head used on compatible gas ranges to direct and distribute the flame for proper cooking. It replaces a damaged or corroded burner head to restore even heating performance. What it does:

• Directs gas to the cooktop for ignition and controlled flame distribution
• Helps maintain even heat across the cooking surface for consistent results
• Can resolve symptoms like uneven flame, visible damage, or poor ignition at the burner
• Works with the burner cap and valve assembly as part of the burner system

• Turn off gas supply and power to the appliance before starting any work
• Remove grates and burner caps to access the burner; follow OEM disassembly guidance
• Replace only with the exact part number to ensure proper fit and function

Approx 1-1/2 inches in diameter

This valve and pipe assembly controls water flow to the refrigerator ice maker and dispenser, restoring reliable water delivery and ice production. It replaces a worn or leaking water inlet assembly to stop drips and restore proper fill cycles. What it does

• Routes and controls water from the household supply to the ice maker and dispenser
• Opens and closes to allow timed water fills for ice production
• Stops water flow when the valve is closed to help prevent leaks
• Commonly used when the ice maker or dispenser does not fill or when visible leaks occur

• One valve and pipe assembly

• Turn off power and shut off the water supply before starting any repair
• Handle the valve and fittings carefully to avoid twisting or damaging water lines
• Use proper tools and replacement gaskets/filters where required; tighten fittings to manufacturer torque specifications

This bake burner is the oven's main gas tube that produces steady heat for baking and roasting, restoring proper cooking temperatures and more consistent bake results. It fits gas ovens that use a separate bake tube assembly. What it does

• Directs and distributes the oven's gas flame to generate baking heat
• Restores proper oven temperature when the bake flame is weak or absent
• Helps eliminate uneven baking or undercooked dishes caused by a failing tube
• Works with the oven igniter and gas valve to light the burner safely

• One bake burner (bake tube) as shown

• Turn off gas supply and electrical power before starting work
• Removal may require disconnecting burner mounting screws and any brackets; keep track of fasteners
• Inspect and replace related parts (igniter, orifice) if ignition problems persist

This burner cap sits over the gas burner head to focus and evenly distribute the flame on your cooktop or range. Replace a missing, chipped, or warped cap to restore smooth ignition and consistent, efficient heating.

• Shapes and diffuses the burner flame for even heat across cookware
• A properly seated cap promotes fast, reliable ignition
• Shields the burner head from spills and debris for consistent performance
• Replaces damaged or missing caps that can cause uneven/yellow flames, delayed ignition, or clicking without lighting

• Disconnect power and shut off gas; allow the surface to cool completely
• Lift off the old cap and clean the burner head/ports before installing
• Match the cap to the correct burner position for your model; caps are size-specific
• Seat the cap flat and centered, then test ignition and flame pattern