Heating Element

This genuine surface heating element replaces a damaged or non-heating top burner so you can restore even cooking and safe stovetop use. Designed to match factory fit and function for compatible electric ranges. What it does:

• Heats cookware by providing a working coil burner for stovetop cooking
• Replaces elements that are visibly damaged, cracked, or won't heat
• Helps resolve burners that heat intermittently or not at all
• Restores normal temperature control when the element is the faulty component

• Disconnect power to the range before servicing to avoid shock hazard
• Remove burner trim or receptacle as needed; element typically lifts out of the socket
• Inspect the terminal/socket for damage and replace if corroded or loose

The Range Bake Element Bottom Heater Sheath is an essential component for maintaining the efficiency of your range's baking function. This genuine OEM part ensures a perfect fit with your Samsung range, providing reliable performance and durability. Designed to protect the bottom of your bake element, it helps prevent damage from spills and debris, extending the lifespan of your appliance. Installing the Range Bake Element Bottom Heater Sheath is straightforward, allowing you to restore your range's functionality quickly and easily. By using this genuine OEM part, you can enjoy consistent and even heating during baking, enhancing your cooking experience. Specifically crafted to meet Samsung's high-quality standards, it guarantees optimal compatibility and performance. Whether you are repairing an older range or replacing a worn-out component, the Range Bake Element Bottom Heater Sheath ensures your appliance operates smoothly and efficiently, providing you with the dependable performance you expect from your kitchen equipment.

The Oven Bake Element is an OEM replacement part for Whirlpool ranges and wall ovens. Located at the top of the oven cavity, it generates infrared heat energy for baking and warming functions. 2500 Watt, 240 Volt. Size: Width 21-3/4"; Length 15-3/8"; Mount bracket to terminals 3"; Space between terminals 19-1/8".

Causes of a bad bake element include electrical malfunctions, physical damage from accidental impacts, and the buildup of residue from spills or splatters. These issues can cause the element to burn out or short-circuit.

Symptoms of a bad bake element include:

• Uneven or inadequate top surface heating during baking
• The premature ending of bake cycles before completion due to lost heating ability
• Error codes displaying problems like thermal cut-outs activating too often
• Visible cracks or fractures in the element coil or insulator ring

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Range Oven Triple Surface Element is an essential component for maintaining the performance of your range oven. This genuine OEM part ensures reliable and efficient heating, allowing you to cook your meals evenly every time. Designed specifically for Samsung range ovens, it guarantees a perfect fit and seamless integration with your appliance. The triple surface design provides versatile cooking options, whether you're baking, broiling, or roasting, giving you greater control over your culinary creations. Installing this heater radiant-triple is straightforward, helping you restore your ovenGÇÖs functionality quickly without the need for professional assistance. By choosing the Range Oven Triple Surface Element , you invest in durability and consistent performance, ensuring your range oven operates at its best for years to come. Enhance your cooking experience with this high-quality genuine OEM part, tailored to meet the standards of Samsung appliances and deliver exceptional results in your kitchen.

This bake element heats the oven cavity for standard baking operations, restoring even heat when the original element fails. It installs at the rear or bottom of the oven cavity to provide the radiant heat needed for baking. What it does:

• Heats the oven cavity to maintain proper baking temperatures.
• Replaces a burned, broken, or visibly damaged element that won't glow or heat.
• Helps correct symptoms like insufficient heat, uneven baking, or an oven that won't reach set temperature.
• Works with the oven's control system and thermostat to deliver steady radiant heat.

• Disconnect power to the appliance before starting — turn off the circuit breaker or unplug the range.
• Allow the oven and old element to fully cool before handling.
• Handle the element carefully to avoid bending or damaging the terminals or ceramic insulators.
• After installation, restore power and test the oven on a bake cycle to ensure the element heats correctly.

Replacement bake element for the lower oven. It supplies the primary heat during Bake cycles so your range can reach and hold the set temperature, restoring consistent, even baking performance when the original element fails.

• Generates the lower-oven heat during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common symptoms: no heat in Bake, won't reach temperature, uneven baking, or a visibly cracked/blistered element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks, take out the element's mounting screws, and gently pull the element forward to access wires
• Transfer one wire at a time to the new element; prevent wires from slipping back into the oven wall
• Reinstall screws, ensure firm connections, restore power, and test Bake

This heater assembly warms the wash water inside the tub so the control can reach and maintain the selected temperature. Replacing a failed element restores proper heating performance and helps return cycle times to normal. What it does:

• Heats the water in the washer's tub during applicable cycles
• Helps the control reach and hold target temperatures for better cleaning
• Failure symptoms can include cold wash water, extended cycle times, and reduced cleaning performance
• Visual damage or an open circuit on the element indicates replacement is needed

• 1 heater assembly

• Disconnect power and turn off water before servicing
• The heater mounts at the bottom of the outer tub; remove front or rear panels as required by your model to access it
• Note wire locations; loosen the center nut, press the stud to release the old seal, and carefully withdraw the element
• Seat the new gasket evenly, tighten the nut to compress the seal, then run a test cycle to check for leaks and proper heating

This radiant surface element sits beneath the glass cooktop and provides heat to a single burner on an electric range. Replacing a failed element restores fast, even heating and reliable temperature control on that cooking zone. What it does:

• Generates radiant heat under the glass for one surface burner
• Works with the control to cycle and maintain the selected temperature
• Common symptoms: burner won't heat, heats slowly or unevenly, or only part of the ring glows
• Visible breaks or damage to the element under the glass

• 1 radiant surface element

• Disconnect power at the breaker before servicing
• Allow the cooktop to cool completely and protect the glass surface
• Lift/remove the glass top to access the element; transfer any brackets/retainers from the old unit if required
• Move wires one at a time to matching terminals and center the element under the burner graphic before reassembly

This surface heating element restores dependable heat to a burner on your range or cooktop. Also called a surface burner or top burner element, it delivers the cooking temperature for that zone when the control sends power. What it does:

• Generates heat for one cooking zone on the cooktop
• Common symptoms: burner won't heat, heats unevenly or only partway, takes too long to heat, or shows visible damage
• Helps isolate a single-burner failure when other surface elements still work
• Replaces a damaged or open element to restore consistent heating

• 1 surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Access the element per your model (remove burner pan or lift the glass top)
• Note/photograph wiring and transfer any brackets or clips; move wires one at a time to matching terminals
• Ensure the element sits flat and all connections are secure before reassembly and testing

This upper broil element sits at the top of the oven cavity to provide intense radiant heat for broiling and finishing. Replacing a burned-out element can restore top-heat performance and consistent, even results.

• Provides direct, high heat from the top during Broil to sear and brown food
• Common symptoms include: no broil heat, uneven top browning, only the bake element heats, visible cracks/blisters, or tripping a breaker from a shorted element
• Works with the oven control to cycle heat and maintain broil temperature
• A failed element typically shows no continuity when tested with a multimeter

• Disconnect power at the circuit breaker and allow the oven to cool completely
• Remove racks; support the element, remove mounting screws, and carefully pull it forward
• Transfer wires one at a time with insulated pliers; prevent leads from slipping back into the insulation
• Avoid bending the element or over-tightening screws; ensure terminals are fully seated, restore power, and test Broil

Restore dependable heat to your indoor grill module with this electric grill element. Replacing a worn or failed element brings back even cooking and consistent searing performance on compatible grill cartridges. What it does:

• Converts electrical power into radiant heat for indoor grilling
• Delivers even heat distribution across the grill area when functioning properly
• Common fix when the grill won't heat, heats slowly, or has cold spots
• Replace if the coil is cracked, blistered, or visibly damaged

• 1 electric grill heating element

• Disconnect power at the breaker or unplug the unit; allow all components to cool completely
• Remove grill grates and any shields or pans to access the element
• Lift the element straight up to disengage from the terminal block; avoid bending terminals and transfer any reusable clips/brackets if present
• Seat the new element fully in the terminals; verify secure connections before reassembly and testing

Restore top-heat performance with this Oven Broil Element. Mounted at the top of the oven, it delivers the radiant heat needed for broiling and finishing, helping ensure quick searing and even browning on the broil setting. What it does:

• Supplies radiant heat from above for broiling and top-browning
• Energizes during broil and any cycle that calls for upper-element heat
• Common symptoms: no broil heat, weak/uneven top browning, visible breaks or blisters on the element, or a tripped breaker when Broil is selected
• Replacing a failed element restores consistent upper-oven heat

• 1 broil element

• Disconnect power at the breaker before servicing
• From inside the oven, remove mounting screws and gently pull the element forward to access terminals
• Secure/label wires so they don't slip back through the rear panel; transfer leads one at a time
• Avoid bending or stressing the new element; ensure terminals are fully seated before restoring power