Heating Element

Oven not heating or baking unevenly? The bake element provides bottom heat for baking and roasting. Easy DIY repair when coils deteriorate from heat cycling.

Oven not heating or heating unevenly? This range bake element restores fast preheating and consistent temperatures. DIY-friendly with basic tools.

Oven not heating evenly in convection mode? This rear convection heating element restores proper temperature. DIY-friendly, typically installs in 10-20 minutes.

If your oven won't heat or bakes unevenly, the bake element may be burned out. This lower heating element is a straightforward DIY fix in under an hour.

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

Broiler won't heat up? This upper heating element restores high-heat broiling and surface browning. Takes about 15 minutes to replace with basic tools.

Fix a broiler that won't heat or a melted element. This range broil element delivers direct radiant heat at the top of your oven during the broil cycle.

Bake element restores oven heat by producing the radiant heat needed for baking and roasting. Replacing a worn or damaged bake element helps the oven reach and maintain set temperatures for more consistent cooking results. What it does:

• Heats the oven cavity to provide direct radiant heat for baking and roasting.
• Use when the element shows visible breaks, blistering, or does not glow when the oven is set to high.
• Common symptom indicators: oven won't reach set temperature, uneven baking, or longer-than-normal cook times.
• Works as a direct replacement for the oven's lower/bake heating element.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Match the part to your model and terminal layout before installing; tighten connections securely.

This bake element heats the small oven cavity from below during Bake, delivering the radiant heat needed for preheating and consistent baking when the original element fails.

• Provides primary bake heat at the bottom of the small oven cavity
• Works with the oven control to preheat and maintain set temperature
• Common failure symptoms: no or weak bake heat, uneven baking, visible blistering/cracks, or a breaker trip when Bake is selected

• Disconnect power at the breaker before servicing
• Access is typically from inside the cavity; remove mounting screws, pull the element forward, and move wires one at a time
• Support wires so they don't retract into the insulation; avoid bending or stressing the new element
• Restore power and run a bake cycle to verify proper heating

Dryer not heating or takes hours to dry? This 240V heating element assembly restores proper heat output. Common fix for no-heat issues. Moderate DIY repair.

This is a triple radiant surface element used on glass-top electric ranges. It provides heat to the cooktop surface and typically features multiple heating zones for different pot sizes. Replace this element if your cooktop burner is not heating evenly, only partially heating, or not turning on at all.

Restore reliable baking performance with this bake heating element. Mounted at the bottom of the oven, it provides the primary heat source in Bake mode so the cavity reaches and maintains the set temperature for consistent results. What it does:

• Heats the oven in Bake mode to reach and hold the set temperature
• Failure can cause no heat in bake, very slow preheating, or uneven/undercooked results
• Visible cracks, blisters, or a broken coil indicate the element should be replaced
• A shorted element may trip a household breaker or blow a fuse

• One bake heating element

• Disconnect power at the breaker and allow the oven to cool before servicing
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wire terminals
• Transfer wires one at a time to the new element; do not allow wires to fall back into the insulation
• Reinstall the element and panels, restore power, and test bake operation

Broiler not heating or browning food properly? This upper broil element restores intense top heat for even broiling. Takes 15-20 minutes to replace.

Main broil heating element for the oven, designed to restore top-heat for broiling and browning. Replaces a failed broil element so the oven can produce even, high-intensity heat during broil cycles. What it does:

• Generates the high, direct heat at the top of the oven used for broiling and browning.
• Restores proper broil performance when the element no longer heats or glows.
• Fixes symptoms such as no broil heat, uneven browning, visible burn marks, or a broken/warped element.
• Works as the primary upper heating element used in broil cycles (main oven).

• Disconnect power to the range/oven at the breaker before starting any work.
• Remove oven racks and access the element from inside the oven; element typically secures with mounting screws and terminal connectors.
• Handle terminals and sharp metal edges carefully; wear gloves and eye protection.

Size: 8 inch. 2200 watt. Radiant.

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.