Lg Gasket & Seal

The Gasket is an OEM part for LG washing machines. This component provides a watertight seal between the door and the drum, preventing leaks during wash and spin cycles.

Common causes of a bad gasket include wear and tear from repeated use, exposure to harsh detergents, or mold and mildew buildup. A compromised gasket can lead to water leakage, reducing the efficiency of the washing machine and potentially causing water damage to the surrounding area.

Symptoms of a bad Gasket include:

• Water leaking from the door area during operation
• Visible cracks, tears, or mold on the gasket
• Unpleasant odors from mold or mildew buildup
• Difficulty closing the door properly

This OEM LG part is also compatible with Sears/Kenmore models.

This genuine replacement gasket restores a tight, reliable seal between mating parts in your appliance to prevent leaks and performance loss. Replacing a worn or damaged gasket helps stop moisture intrusion and keeps the unit operating as designed.

• Forms a compressible barrier to keep air or water from escaping at the joint
• Helps maintain proper operation and efficiency by preserving the intended seal
• Common failure signs: leaks or drips, visible cracks/tears or flattening, hardening/brittleness, or gaps that won't stay closed

• Disconnect power and, if applicable, shut off the water supply before service
• Clean and dry all sealing surfaces; remove old residue or adhesive
• Seat the gasket evenly without stretching; press for full contact all around
• Let the gasket relax at room temperature (or warm slightly) to ease fit, then check the seal after reassembly

The Gasket is an OEM part for LG washing machines. This part forms a seal around the washer door, preventing water from leaking out during wash cycles.  

Causes of a bad gasket can include continuous exposure to water and detergent, mold or mildew buildup, and wear and tear from frequent opening and closing of the washer door. 

Symptoms of a bad gasket include:

• Water leaking from the washer door during operation
• Visible cracks, tears, or deformities in the gasket
• Mold or mildew buildup on the gasket
• The door not sealing properly, leading to inefficient washing

This OEM LG part is also compatible with some Kenmore models.

This door gasket seals the dryer door opening to keep heat and moisture inside the drum. Replacing a worn gasket helps restore proper airflow and drying performance while reducing lint and warm air leaking around the door.

• Creates a tight seal between the door and front panel to prevent air leaks
• Helps maintain correct airflow for efficient, consistent drying
• Reduces escaping heat and humidity around the door area
• Common signs it's failing: visible wear or tears, flattened/compressed gasket, lint accumulation near the door, longer dry times, warm air leaking when the door is closed

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the door assembly as needed and separate door panels to access the gasket (procedure varies by model)
• Remove the old gasket and clean the mating groove/surface of residue and debris
• Press the new gasket fully and evenly into place; align the seam, reassemble the door, and verify an even seal

This flexible door boot seal forms a watertight barrier between the washer tub and front panel. Replacing a damaged boot helps stop leaks, reduces odors from trapped residue, and restores smooth door operation.

• Seals the door opening to keep wash water inside the tub during all cycles
• Helps prevent leaks at the front of the machine
• Common failure signs include water dripping from the door area, visible tears or moldy buildup, and musty odors
• May also cause error codes or wet floors during or after a cycle

• Disconnect power and turn off water supplies before starting
• Remove the front door clamp, front panel/clamps as needed, and transfer any attached hoses or ports to the new boot
• Align drain port(s) and index marks carefully; seat inner and outer clamps fully
• After installation, run a quick rinse to check for leaks

The Freezer Door Gasket is an OEM part for LG refrigerators. This gasket is designed to fit around the perimeter of the freezer door, creating an airtight seal that prevents warm air from entering and cold air from escaping. This ensures the freezer maintains a consistent temperature, which is essential for preserving food quality and reducing energy consumption.

Causes of a bad door gasket can include wear and tear from frequent use, exposure to harsh cleaning chemicals, or physical damage from sharp objects or accidental impacts.

Symptoms of a bad freezer door gasket include:

• The freezer door not closing properly
• Visible cracks, tears, or deformities in the gasket
• Frost or ice buildup inside the freezer
• Increased energy consumption due to the freezer working harder to maintain temperature

This OEM LG part is also compatible with Sears/Kenmore models.

This thermistor seal is the grommet that seals the temperature sensor where it passes through the washing machine's outer tub. Replacing a worn seal restores a watertight fit and helps prevent leaks that can damage surrounding components. What it does

• Forms a watertight barrier around the tub temperature sensor (thermistor)
• Helps keep the sensor securely positioned in the mounting port
• Common failure symptoms: water leaking during cycles, puddles under the unit, visible cracking/hardening of the grommet, or a loose sensor fit

• 1 thermistor seal

• Disconnect power and water; drain any remaining water from the tub
• Access the thermistor on the outer tub, disconnect its harness, and remove the sensor
• Pull out the old seal, clean the opening, press in the new seal, and reinstall the sensor fully seated
• Run a brief test cycle and check for leaks before final reassembly

This door boot gasket seals the opening between the washer door and the front of the outer tub. Replacing a damaged or deformed boot stops front leaks and restores a tight, reliable seal.

• Forms a watertight seal between the door and outer tub to contain wash water
• Helps maintain proper door closure
• Common signs of failure: water leaking from the door/front, visible tears or cracks, loose or misshapen boot, residue that returns after cleaning

• Disconnect power and turn off water supply before servicing
• Remove the outer and inner retaining bands; note the gasket's orientation and any drain ports
• Seat the new gasket evenly on the tub lip; reinstall clamps securely and verify the seal all the way around
• Run a short test cycle to check for leaks before returning to service

The Drum Seal is an OEM part for LG dryers. It forms an airtight seal between the rotating drum and stationary outer housing. This seal prevents air leakage that could diminish drying effectiveness.

Causes of a bad drum seal can include cracks or breaks from heat cycling over time, hardening and failure of rubber seal materials, or physical damage from cleaning tools or debris inside the drum.

Symptoms of a bad drum seal include:

• Slow or incomplete drying times
• Clothes not feeling fully dry at the end of cycles
• Excessively long heating cycles
• Noticeable air drafts around the dryer housing

This OEM LG part is also compatible with some Kenmore models.

This flexible perimeter seal keeps the refrigerator door closing tight so cold air stays in and warm air stays out. Replacing a worn or warped gasket helps restore stable temperatures, reduce frost and condensation, and improve overall efficiency.

• Creates an airtight seal around the door to maintain interior temperature and humidity
• Helps prevent condensation, sweating, and frost at the door opening
• Restores proper door closure when the old seal is torn, deformed, or compressed
• Common symptoms: visible gaps or cracks, moisture around the door, temperature fluctuations, longer run times

• Disconnect power and clear items from door bins before servicing
• Pull the old gasket from the retaining channel; some models require loosening retainer screws
• Clean the channel/mating surface; warm the new gasket with hot water or low heat to relax folds
• Seat the new gasket starting at the corners, then along the sides; close the door and check for even contact all around

This gasket creates a watertight seal between mating parts in the dishwasher's water system. Replacing a worn or damaged seal helps stop leaks during cycles and maintains proper wash performance. What it does:

• Seals the joint between components such as the sump, pump housing, or inlet assemblies
• Prevents water leakage under pressure during fill, wash, and drain
• Helps maintain spray pressure by reducing internal bypass
• Common symptoms include water on the floor or in the base pan, and a flattened, cracked, or brittle old gasket

• One gasket

• Disconnect power and turn off the water supply before servicing
• Access the gasket location and remove any retaining hardware
• Remove the old gasket and clean both sealing surfaces thoroughly
• Seat the new gasket evenly without twisting; tighten fasteners/clamps uniformly and run a test cycle to check for leaks

Replace a worn door gasket to restore a tight seal on your refrigerator door. This perimeter seal keeps cold air in and humid air out to stabilize temperatures, reduce frost and condensation, and support efficient, consistent cooling.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and humidity
• Reduces frost, sweating, and energy loss from air leaks
• Common symptoms: torn or hardened gasket, visible gaps, door not sealing, moisture or frost near the door

• Disconnect power before servicing
• Warm the new gasket in hot water or with a hair dryer on low to relax and straighten it
• Remove the old gasket and clean the mounting channel and mating surfaces
• Install starting at the corners and press fully into the channel; verify even contact and proper door closure

This gasket does not include the port. For the gasket with a port order MDS33059402.

This dishwasher sump gasket seals the joint between the sump assembly and the tub to prevent leaks and maintain wash performance. Replace it if the old seal is worn, flattened, cracked, or damaged to stop water escaping beneath the unit.

• Creates a watertight seal where the sump attaches to the tub
• Helps prevent water leaks from the base of the dishwasher
• Supports proper circulation and overall wash performance
• Common failure signs: puddles under the unit, leaks during a cycle, or a visibly torn/deformed gasket

• Disconnect power and turn off the water supply before servicing
• Access the sump from inside the tub (remove lower rack, spray arm, filters, and sump cover) or from below, depending on model
• Clean mating surfaces; install the new gasket evenly without twists or gaps
• Reassemble and run a short cycle to check for leaks

The door boot gasket seals the opening between your front-load washer's door and outer tub, keeping wash water contained. Replace it if the boot is torn, deformed, or heavily mildewed to restore a reliable, watertight seal.

• Forms a watertight seal between the outer tub and door opening
• Prevents leaks from the front of the washer during wash and spin
• Flexible design maintains the seal as the drum moves
• Common failure signs: water on the floor at the front, dripping at the door, visible rips/cracks, or the boot pulling loose

• Unplug the washer and turn off water supply; wear gloves to avoid sharp edges
• Access the boot by removing panels as required for your model; note hose positions and alignment
• Release the outer and inner retaining clamps/springs and remove the old gasket
• Seat the new gasket evenly, align indexing features/ports, reinstall clamps securely, and run a quick test for leaks

This door gasket forms the perimeter seal between the appliance door and cabinet to keep air and moisture contained. Replacing a worn gasket restores a reliable, leak-resistant seal and proper door performance. What it does:

• Seals the door perimeter to prevent air and moisture from escaping
• Helps the appliance maintain proper internal conditions
• Common failure signs: tears, cracks, or warping; gaps along the seal; door not sealing fully; moisture or drips at the door edge; excess frost near the door on cooling appliances

• One door gasket

• Disconnect power before servicing; turn off gas or water supply if applicable
• Allow heat-producing appliances to cool completely before starting
• Remove the old gasket and clean the mating surfaces thoroughly
• Press the new gasket evenly into the channel or onto retainers; check door closure