Valve

Dishwasher overfilling or won't stop filling? This float switch lever activates the water level sensor. Simple DIY fix restores proper fill control.

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery when the system won't fill or dispense. Direct-fit replacement that helps stop leaks and restore function. What it does:

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when the fill cycle or dispense cycle ends
• Common part to replace for slow/no ice production or no water from dispenser
• Replaced when valves leak or water lines fail to pressurize

• Disconnect power and shut off the water supply before starting work
• Verify tubing connections and electrical connector orientation before reassembly
• Inspect supply lines and gaskets; use proper replacement fittings if damaged

No water from dispenser or ice maker not filling? This dual-solenoid water inlet valve controls flow to both systems. Direct replacement restores operation.

This solenoid valve is the electrical valve assembly that opens and closes to control fluid flow in the appliance, restoring proper fill and shutoff behavior when the original valve fails. What it does:

• Electrically opens and closes to allow or stop fluid flow to the appliance
• Stops unintended flowing or leaking when the valve seals properly
• Commonly linked to symptoms such as no fill, continuous filling, intermittent fill, or leaks near the valve
• Works as the actuator controlled by the appliance's control board to meter fluid delivery

• Disconnect power and shut off the water supply before servicing.
• Handle valve connections and seals carefully; replace any damaged gaskets or hoses.
• Reconnect wiring to the correct terminals and secure all fittings to avoid leaks.
• Test appliance through a full cycle after install and check for leaks.

Fix low water flow or FL error code issues with this washer water inlet valve. Controls water flow into your machine. Moderate DIY repair, 30-45 minutes.

Fix burners that won't ignite or have weak flames with this gas control valve. Restores proper gas flow and flame control. Moderate DIY repair.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

This water inlet valve assembly controls water flow into the washer tub, restoring correct fill and water selection so cycles start and run properly. It replaces a failed or leaking inlet valve to help the machine fill and pause as designed. What it does

• Opens and closes to allow cold and/or hot water into the washer during fill cycles
• Stops water flow when the machine reaches the set fill level
• Commonly replaces valves that leak, fail to fill, or cause the washer to overfill
• Works with the washer's control signals to route water only when needed

• Disconnect power and shut off household water supply before replacing the valve
• Tighten fittings to correct torque to avoid leaks; use new seals if provided or recommended

No water or ice? This inlet valve assembly controls water flow to your refrigerator's dispenser and ice maker, restoring fill function in under an hour.

Fix gas leaks or burners that won't ignite with this cooktop gas valve. Controls gas flow to burner assembly for safe ignition and consistent heat.

Fix a refrigerator that won't dispense water or ice with this water inlet valve. Controls water flow to the dispenser and ice maker. Easy DIY repair.

Fix a burner that won't ignite, won't turn off, or has weak flame with this range top burner valve. Moderately difficult repair for most DIYers.

Fix a burner that won't light, won't stay lit, or has uneven flames with this top burner valve. Controls gas flow to individual burners on gas cooktops.