Valve

Fix water leaking into your washer when off or during cycles. This dual inlet valve controls hot and cold water flow. Accessible from the top panel.

Gas won't flow to burner or oven won't light? Safety valve controls gas flow to the burner assembly. Common fix when igniter glows but oven won't ignite.

Fix water leaking onto the floor or high-pitched squealing during fill. This washer water inlet valve is a common fix. DIY repair takes about 2 hours.

This dome float is the replacement water-level float that helps the appliance sense and control the tub's water level, restoring reliable fill and shutoff behavior. Use this OEM-fit float when the original is cracked, stuck, or missing. What it does:

• Moves with rising and falling water to actuate the water-level mechanism and help prevent overfilling.
• Can reduce symptoms such as improper fill levels, continuous filling, or intermittent fill shutoff when the existing float is damaged or obstructed.
• Works as part of the washer's water sensing system—does not include electronic switches or housings unless shown.

• Disconnect power and unplug the appliance before starting any repair.
• Access may require removing the washer top or cabinet; follow your model's service instructions.
• Inspect surrounding hoses and clips; replace any damaged components and ensure the float moves freely.

Fix your refrigerator not filling with water or overfilling with this water inlet valve. Controls water flow during fill cycles. Easy DIY repair.

Fix a refrigerator not dispensing water or making ice with this water inlet valve replacement. Common repair for no water flow to dispenser or icemaker.

This is a gas valve for a range cooktop that regulates the flow of gas to a surface burner. It connects to the control knob and allows you to adjust the flame size from simmer to high heat. Replace this valve if the burner won't ignite, the flame is inconsistent, the knob feels loose or unresponsive, or you smell gas when the burner is turned off.

Fixes burner that won't light or clicks but doesn't ignite. This valve controls gas flow to restore reliable ignition and heat control on your range.

This solenoid valve is the electrical valve assembly that opens and closes to control fluid flow in the appliance, restoring proper fill and shutoff behavior when the original valve fails. What it does:

• Electrically opens and closes to allow or stop fluid flow to the appliance
• Stops unintended flowing or leaking when the valve seals properly
• Commonly linked to symptoms such as no fill, continuous filling, intermittent fill, or leaks near the valve
• Works as the actuator controlled by the appliance's control board to meter fluid delivery

• Disconnect power and shut off the water supply before servicing.
• Handle valve connections and seals carefully; replace any damaged gaskets or hoses.
• Reconnect wiring to the correct terminals and secure all fittings to avoid leaks.
• Test appliance through a full cycle after install and check for leaks.

Dishwasher overfilling or won't stop filling? This float switch lever activates the water level sensor. Simple DIY fix restores proper fill control.

If your range burner won't ignite, stays on high, or has uneven flames, the top burner valve may be faulty. This valve controls gas flow to each burner.

No water from dispenser or ice maker not filling? This dual-solenoid water inlet valve controls flow to both systems. Direct replacement restores operation.

This is a gas valve that controls the flow of gas to a surface burner on a gas range or cooktop. It connects to the burner control knob and regulates the flame from high to low settings. Replace this valve if a burner will not ignite, the flame cannot be adjusted properly, you smell gas when the knob is in the off position, or the knob turns without resistance.

Fix burners that won't ignite or have weak flames with this gas control valve. Restores proper gas flow and flame control. Moderate DIY repair.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

No water or ice? This inlet valve assembly controls water flow to your refrigerator's dispenser and ice maker, restoring fill function in under an hour.