Washer Dryer Combo Parts

Insulates and supports electrical connections through the dryer chassis. Replace if cracked, heat-damaged, or broken to prevent shorts and restore safety.

Color: white. Measures about 2 inches in Diameter.

This is a factory switch used in the appliance's control/safety circuit. Replacing a worn or failed switch restores reliable signaling so the selected function engages properly and the unit responds consistently to user inputs and status conditions.

• Provides an electrical on/off signal to the control or safety circuit
• If faulty, selected functions may not activate or may be intermittent
• Can trigger error codes related to a switch input, depending on model

• Disconnect power before servicing; turn off gas/water if applicable
• Note/photograph wire locations and transfer connectors one at a time
• Verify actuator alignment and secure mounting before reassembly
• After installation, run a test cycle to confirm proper operation

Replaces a frayed, melted, or damaged power cord on your washer. Restores grounded connection from wall outlet to internal power circuit.

Channels household water to your washer's fill system. Replace if cracked, leaking, or worn to restore proper flow and prevent water damage to floors.

The Door Gasket is an OEM part for GE dryers. This seal prevents hot air from escaping during a cycle, ensuring that the dryer operates efficiently and safely. The gasket's primary role is to maintain the internal temperature and airflow, which are essential for the drying process.  

Causes of damage to the door gasket often involve regular wear and tear from opening and closing the dryer door.  

Symptoms of a bad Door Gasket include:

• Clothes taking longer to dry or not drying fully due to heat escaping from the dryer.
• An increase in energy consumption as the dryer works harder to maintain the required temperature.
• Visible wear, tears, or gaps in the gasket 
• Heat leakage from around the dryer door 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

Water leaking into the tub or not filling properly? This inlet valve controls water flow into your laundry center. Moderate DIY repair—about 1 hour.

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Seals the top of the outer tub to prevent leaks and splashing. Replace if cracked, worn through, or gasket is compressed causing water to escape onto the floor.

Seals the lower dryer door to prevent heat loss and ensure efficient drying. Replace if worn, cracked, or air is escaping. Verify fit with your model.

Washer won't respond to cycle selections? This selector switch mounts behind the control knob to restore reliable setting changes. Easy DIY fix.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tension to the idler pulley to keep the drive belt tight around the drum and motor
• Helps resolve a drum that won't turn or tumbles intermittently
• Addresses belt issues such as slipping off, appearing loose, or premature breakage from low tension
• Can reduce squealing/chirping from the idler area caused by belt slip

• 1 idler spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the idler assembly by removing the front or lower access panel per your model
• Relieve belt tension, unhook the old spring from the idler arm/frame, and install the new spring in the same orientation and holes
• Rotate the drum by hand to check smooth operation before reassembly

Idler arm assembly mounts to the dryer frame and maintains proper belt tension on the drum. Replace if the arm is cracked, bent, or the pulley is worn.

Seals between the outer tub and splash guard to prevent leaks during wash and spin cycles. Replace if water leaks from the top of the cabinet. Confirm fit by model number.

Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.